收藏 分享(赏)

ASTM_D_6073_-_08a_2020.pdf

上传人:益****师 文档编号:174103 上传时间:2023-03-04 格式:PDF 页数:3 大小:81.06KB
下载 相关 举报
ASTM_D_6073_-_08a_2020.pdf_第1页
第1页 / 共3页
ASTM_D_6073_-_08a_2020.pdf_第2页
第2页 / 共3页
ASTM_D_6073_-_08a_2020.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D607308a(Reapproved 2020)Standard Test Method forRelative Setting of Heatset Printing Inks1This standard is issued under the fixed designation D6073;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio

2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method describes the procedure for determin-ing the relative setting speed of heatset inks using a testerconsisting of a forc

3、ed hot air oven and print delivery system.1.2 This test method is applicable to printing inks intendedto be dried by the application of heat and for which a suitablereference standard is available.1.3 Although heatset inks are normally printed by the offsetprocess,this test method specifies the dire

4、ct letterpress modebecause the higher ink film thicknesses obtained tend toamplify subtle differences in ink setting speed.Prints areprepared by a flatbed printing apparatus using a constant depthprinting gage.1.4 This tester reads temperature and belt speed in nonmet-ric terms;therefore,instrument

5、settings in this test method arestated first in U.S.Customary Units(inch pound units ofmeasurements).The values given in parentheses are for infor-mation only.1.5 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI uni

6、ts that are provided for information onlyand are not considered standard.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and

7、 deter-mine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-me

8、ndations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D6846 Practice for Preparing Prints of Paste Printing Inkswith a Printing Gage3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 heatset printing ink,

9、nan ink typically containingaliphatic hydrocarbon solvents that evaporate at elevatedtemperatures.4.Summary of Test Method4.1 A printing gage is used to prepare a laboratory printcontaining both the test sample and a standard ink.The freshlyprepared print is immediately subjected to forced hot air i

10、n thetester,which is initially set at 350F(177C)and a belt speedof 30 fpm(0.15 m/s).4.2 The print is cooled,overlaid with a clean sheet of stock,passed through the printing apparatus,and examined for setoff.4.3 The process is repeated at different belt speeds ortemperatures until either the test sam

11、ple or the standardexhibits setoff and the other does not,or it is established thatboth are the same.The sample is then reported to dry fasterthan,slower than,or equal to the standard.5.Significance and Use5.1 The setting speed of heatset printing inks is importantbecause it influences the efficienc

12、y of the drying process.Thistest method provides a means for comparing the setting of aheatset ink directly against a standard at the same conditions oftemperature and exposure time.While the method does notdetermine the setting speed of an ink on a production press,itis useful for specification acc

13、eptance between the supplier andthe customer.5.2 The setting speed of a printing ink depends on a numberof variables such as the substrate on which it is printed,the filmthickness on the print,the temperature of the forced air,the rateof air flow,and the time that the print is subjected to heat.For1

14、This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.56 on Printing Inks.Current edition approved June 1,2020.Published July 2020.Originally approvedin 1996.Last previous edition a

15、pproved in 2013 as D6073 08a(2013).DOI:10.1520/D6073-08AR20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyri

16、ght ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.these reasons,it is important to conduct the tests underconditions that are controll

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2