1、Designation:D653200(Reapproved 2014)Standard Test Method forEvaluation of the Effect of Clear Water Repellent Treatmentson Water Absorption of Hydraulic Cement MortarSpecimens1This standard is issued under the fixed designation D6532;the number immediately following the designation indicates the yea
2、r oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method evaluates the effectiveness of clearwater rep
3、ellents on hydraulic cement mortar specimens basedon water absorption after a water soak.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associat
4、ed with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2C109/C109M Test Method for Compressive Strength ofHydraulic Cem
5、ent Mortars(Using 2-in.or 50-mm CubeSpecimens)D1475 Test Method For Density of Liquid Coatings,Inks,and Related ProductsD3924 Specification for Environment for Conditioning andTesting Paint,Varnish,Lacquer,and Related MaterialsE145 Specification for Gravity-Convection and Forced-Ventilation Ovens3.T
6、erminology3.1 Definitions of Terms Specific to This Standard:3.1.1 clear water repellent,na coating formulated for thepurpose of protecting porous substrates by reducing the pen-etration of liquid water.4.Summary of Test Method4.1 The masonry unit is immersed in a clear water repellent,removed and a
7、llowed to cure at ambient condition for 7 days.Any deviations should be noted in 10.1.2.After cure,themasonry unit is weighed and placed in water to a depth of 6.3mm(14in.)for 3 days.After the immersion period,themasonry unit is removed and reweighed.The water repellencyvalue of the treatment is the
8、n calculated using a comparison tountreated control specimens.5.Significance and Use5.1 Siliceous alkaline substrates are subject to water damagethat may result in deterioration.Water repellents can provideprotection of siliceous alkaline substrates exposed to water.This test method is used to evalu
9、ate the efficacy of clear waterrepellents on alkaline substrates.6.Apparatus6.1 Forced Draft Oven,Type 1B,in accordance with theType Section of Specification E145.6.2 Balance,having a capacity of not less than 400 g,andsensitivity of 0.01 g.6.3 Reservoir Water Pan,capable of maintaining the waterlev
10、el at 6.3 mm(14in.)in depth with noncorroding rods for thespecimens to sit off the bottom.6.4 Stiff Bristle Brush,to brush the masonry units.6.5 Pressurized Air Source,to blow residual material off thebrushed masonry units.6.6 Stopwatch.7.Reagents and Materials7.1 Masonry Units,51 by 51 by 51 mm(2 b
11、y 2 by 2 in.)masonry units prepared in accordance with procedures outlinedin Test Method C109/C109M with the form release oil re-moved can be used.8.Procedure8.1 Select substrates needed,brush,and blow off dust withpressurized air.The specimens must be free of loose material1This test method is unde
12、r the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.47 on Concrete,Stone and Masonry Treatments.Current edition approved Dec.1,2014.Published December 2014.Originallyapproved in 2000.Last previous editio
13、n approved in 2006 as D6532 00(2006).DOI:10.1520/D6532-00R14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyr
14、ight ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 that may be lost and alter the weight.They also must be free ofmaterial that will alter the absorption characteristics.8.2 Label each piece.Run triplicate samples for each waterrepellent treatmen
15、t.Also include three untreated controlsamples for each series.All specimens in one series of testingshould come from the same lot of masonry units.NOTE1To make comparison between test series,a positive controlneeds to be included.For example,when using mortar cubes,40%isobutyltrimethoxysilane in sol
16、vent can be used as a positive control ineach series.8.3 For the specimen to be treated,measure the surface areaof each test specimen to the nearest 5 mm2(0.1-in.2)and weighto the nearest 0.1 g.Record the weight and area of the uncoatedtest specimens.8.4 Dry the required number of specimens in a forced draftoven,as specified in Specification E145,at a temperature of 806 5C until a constant weight has been reached.A constantoven weight shall be assumed when the specimen weighed tothe nearest 0.1
