1、Designation:D664182British Standard 4457Designation 177/96Standard Test Method forAcid Number of Petroleum Products by PotentiometricTitration1This standard is issued under the fixed designation D664;the number immediately following the designation indicates the year oforiginal adoption or,in the ca
2、se of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTESubsection 13.3.1 and a statement in the Summary of Changes were corrected editorially in December 201
3、8.2NOTESubsections 16.1.1.1 and 16.1.2.1 were corrected editorially in January 2019.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method covers procedures for the determina-tion of acidic constituents in petroleum products,lubricants,biodi
4、esel,and blends of biodiesel.1.1.1 Test Method AFor petroleum products and lubricantssoluble or nearly soluble in mixtures of toluene and propan-2-ol.It is applicable for the determination of acids whosedissociation constants in water are larger than 109;extremelyweak acids whose dissociation consta
5、nts are smaller than 109do not interfere.Salts react if their hydrolysis constants arelarger than 109.The range of acid numbers included in theprecision statement is 0.1 mg g KOH to 150 mg g KOH.1.1.2 Test Method BDeveloped specifically for biodieseland biodiesel blends with low acidity and slightly
6、 differentsolubility.This test method requires the use of an automatictitrator with automatic endpoint-seeking capability.NOTE1In new and used oils,the constituents that may be consideredto have acidic characteristics include organic and inorganic acids,esters,phenolic compounds,lactones,resins,salt
7、s of heavy metals,salts ofammonia and other weak bases,acid salts of polybasic acids,and additionagents such as inhibitors and detergents.1.2 The test method may be used to indicate relativechanges that occur in oil during use under oxidizing conditionsregardless of the color or other properties of
8、the resulting oil.Although the titration is made under definite equilibriumconditions,the test method is not intended to measure anabsolute acidic property that can be used to predict perfor-mance of oil under service conditions.No general relationshipbetween bearing corrosion and acid number is kno
9、wn.NOTE2The acid number obtained by this standard may or may not benumerically the same as that obtained in accordance with Test MethodsD974 and D3339.There has not been any attempt to correlate this methodwith other non-titration methods.NOTE3A few laboratories have made the observation that there
10、is adifference in Test Method D664 results when aqueous versus nonaqueousbuffers are used.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,associat
11、ed with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognize
12、d principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D974 Test Method for Acid and
13、 Base Number by Color-Indicator TitrationD1193 Specification for Reagent WaterD3339 Test Method forAcid Number of Petroleum Productsby Semi-Micro Color Indicator TitrationD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4177 Practice for Automatic Sampling of Petroleum andPetrol
14、eum Products1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.06 on Analysis of Liquid Fuels and Lubricants.Current edition approved Nov.1,2018.Published November 2018.Originallyappro
15、ved in 1942.Last previous edition approved in 2017 as D664 17a.DOI:10.1520/D0664-18E02.This test method was adopted as a joint ASTM-IP standard in 1964.ASTM TestMethod D4739 has been developed as an alternative to the base number portion ofD664.2For referenced ASTM standards,visit the ASTM website,w
16、ww.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on
