1、Designation:D610913Standard Test Methods forFlexural Properties of Unreinforced and Reinforced PlasticLumber and Related Products1This standard is issued under the fixed designation D6109;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revisi
2、on,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 These test methods are suitable for determining theflexural properties for any solid or hollow manufactured
3、 plasticlumber product of square,rectangular,round,or other geomet-ric cross section that shows viscoelastic behavior.The testspecimens are whole“as manufactured”pieces without anyaltering or machining of surfaces beyond cutting to length.Assuch,this is a test method for evaluating the properties of
4、plastic lumber as a product and not a material property testmethod.Flexural strength cannot be determined for thoseproducts that do not break or that do not fail in the extremeouter fiber.1.2 Test Method Adesigned principally for products in theflat or“plank”position.1.3 Test Method Bdesigned princi
5、pally for those productsin the edgewise or“joist”position.1.4 Plastic lumber currently is produced using several dif-ferent plastic manufacturing processes.These processes utilizea number of diverse plastic resin material systems that includefillers,fiber reinforcements,and other chemical additives.
6、Thetest methods are applicable to plastic lumber products wherethe plastic resin is the continuous phase,regardless of itsmanufacturing process,type or weight percentage of plasticresin utilized,type or weight percentage of fillers utilized,typeor weight percentage of reinforcements utilized,and typ
7、e orweight percentage of other chemical additives.1.4.1 Alternative to a single resin material system,diverseand multiple combinations of both virgin and recycled thermo-plastic material systems are permitted in the manufacture ofplastic lumber products.1.4.2 Diverse types and combinations of inorga
8、nic andorganic filler systems are permitted in the manufacturing ofplastic lumber products.Inorganic fillers include such materi-als as talc,mica,silica,wollastonite,calcium carbonate,and soforth.Organic fillers include lignocellulosic materials made orderived from wood,wood flour,flax shive,rice hu
9、lls,wheatstraw,and combinations thereof.1.4.3 Fiber reinforcements used in plastic lumber includemanufactured materials such as fiberglass(chopped orcontinuous),carbon,aramid and other polymerics;orlignocellulosic-based fibers such as flax,jute,kenaf,and hemp.1.4.4 A wide variety of chemical additiv
10、es are added toplastic lumber formulations to serve numerous different pur-poses.Examples include colorants,chemical foaming agents,ultraviolet stabilizers,flame retardants,lubricants,anti-staticproducts,biocides,heat stabilizers,and coupling agents1.5 The values stated in inch-pound units are to be
11、 regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the use
12、r of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulator limitations prior to use.NOTE1There is no known ISO equivalent to this standard.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD883 Ter
13、minology Relating to PlasticsD2915 Practice for Sampling and Data-Analysis for Struc-tural Wood and Wood-Based ProductsD5033 Guide for Development ofASTM Standards Relatingto Recycling and Use of Recycled Plastics(Withdrawn2007)3D5947 Test Methods for Physical Dimensions of SolidPlastics SpecimensE4
14、 Practices for Force Verification of Testing MachinesE691 Practice for Conducting an Interlaboratory Study to1These test methods are under the jurisdiction of ASTM Committee D20 onPlastics and are the direct responsibility of Subcommittee D20.20 on Plastic Lumber(Section D20.20.01).Current edition a
15、pproved June 1,2013.Published June 2013.Originallyapproved in 1997.Last previous edition approved in 2010 as D6109-10.DOI:10.1520/D6109-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume inf
16、ormation,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 Determine the Precision of a Test Method3.Terminology3.1 Definitions:3.1.1 Definitions of terms applying to these test methodsappear in Terminology D883 and Guide D5033
