1、Designation:D576013Standard Specification forPerformance of Manual Transmission Gear Lubricants1This standard is issued under the fixed designation D5760;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A num
2、ber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification lists the test methods and acceptancecriteria for determining the acceptability of lubricants used innonsynchronized heavy
3、 duty manual transmissions.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.2.Referenced Documents2.1 ASTM Standards:2D130 Test Method for Corrosiveness to Copper from Petro-leum Products by Copper Strip TestD892 Test Method f
4、or Foaming Characteristics of Lubricat-ing OilsD5182 Test Method for Evaluating the Scuffing Load Ca-pacity of Oils(FZG Visual Method)D5579 Test Method for Evaluating the Thermal Stability ofManual Transmission Lubricants in a Cyclic DurabilityTestD5662 Test Method for Determining Automotive Gear Oi
5、lCompatibility with Typical Oil Seal ElastomersD5704 Test Method for Evaluation of the Thermal andOxidative Stability of Lubricating Oils Used for ManualTransmissions and Final Drive Axles2.2 Federal Standards:3Federal Standard No.791C,Method 3430.2 CompatibilityCharacteristics of Universal Gear Lub
6、ricantsFederal Standard No.791C,Method 3440.1 Storage Solu-bility Characteristics of Universal Gear Lubricants2.3 SAE Publications:4SAE J2360 Lubricating Oil,Gear Multipurpose(Metric)Military Use3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 nonsynchronized transmission,na tra
7、nsmission hav-ing no means for synchronizing the speeds of engagingelements.Typical heavy-duty manual transmissions have nosuch means for gear engagement by the shift lever,but mayhave such means for pneumatic engagement of auxiliary rangegears.3.1.2 oil seal compatibility,nin lubricants for lubrica
8、tingmanual transmissions and final drive axles,prevention ofchemical or thermal degradation of seal elastomers typicallyobserved as hardening,cracking,or excessive swelling in amanner which would result in oil leakage.3.1.3 thermal oxidation,nin lubricants used for lubricat-ing manual transmissions
9、and final drive axles,deterioration ofthe lubricant under high-temperature conditions which isobserved as viscosity increase of the lubricant,insolublesformation in the lubricant,deposit formation on the parts,or acombination thereof.4.Performance Classification4.1 API Category MT-1The designation A
10、PI CategoryMT-1 identifies the category of lubricants intended for use innonsynchronized manual transmissions,apart from API Ser-vice Category GL-4.See Appendix X1 for background infor-mation on this category.5.Performance Requirements5.1 API Category MT-1 performance requirements for can-didate gea
11、r lubricants are provided in Table 1.6.Number of Tests and Retests6.1 Test Method D5704In determining whether an oilmeets the required limits the following rules shall apply:6.1.1 No more than three operationally valid tests are to beconducted for compliance testing.1This specification is under the
12、jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.B0.03 on Automotive Gear Lubricants&Fluids.Current edition approved June 15,2013.Published July 2013.Originallyapproved in 1995.Last previous edition approved in 2009 as D5760 0
13、9.DOI:10.1520/D5760-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from U.S.Government Printing Off
14、ice Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.4Available from SAE International(SAE),400 Commonwealth Dr.,Warrendale,PA 15096-0001,http:/www.sae.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM Inter
15、national,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.1.2 L-60-1 data used for API Category MT-1 approvalcannot be generated prior to ASTM Test Monitoring Center(TMC)5calibration of the stand for all API Category MT-1parameters.Stand bias adjustment factors base
16、d on referenceoil test results are applied when appropriate.6.1.3 After applying any appropriate stand bias adjustmentfactors,the first test shall meet or exceed all limits.6.1.4 After two tests,the average of the two results on allparameters shall meet or exceed the limits.6.1.5 After three tests,one test is excluded in its entirety.The average of the two results on all parameters shall meet orexceed the limits.6.2 Test Method D5662This test method includes testingon two different elastomer mat
