1、Designation:D582722Standard Test Method forAnalysis of Engine Coolant for Chloride and Other Anionsby Ion Chromatography1This standard is issued under the fixed designation D5827;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the ye
2、ar of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the chemical analysis of enginecoolant for chloride ion by high-performance ion chromatog-ra
3、phy(HPIC).Several other common anions found in enginecoolant can be determined in one chromatographic analysis bythis test method.1.2 This test method is applicable to both new and usedengine coolant.1.3 Coelution of other ions may cause interferences for anyof the listed anions.In the case of unfam
4、iliar formulations,identification verification should be performed by either orboth fortification and dilution of the sample matrix with theanions of interest.1.4 Analysis can be performed directly by this test methodwithout pretreatment,other than dilution,as required by thelinear ranges of the equ
5、ipment.Table 1 indicates severalapplicable anions and approximate detection limits.1.5 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with
6、 its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to its use.1.7 This international standard was developed in accor-dance with internationally recognized p
7、rinciples on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent
8、WaterD1176 Practice for Sampling and Preparing Aqueous Solu-tions of Engine Coolants orAntirusts for Testing PurposesE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test MethodE177 Practice for Use of the Terms Precision and Bias inASTM Test Methods3.Summary of T
9、est Method3.1 A small volume of working sample is prepared bydilution of the sample with the method eluant.This dilutedsample is filtered and pumped through two ion exchangecolumns and a suppressor and into a conductivity detector.Ionsare separated based on their affinity for exchange sites of there
10、sin with respect to the resins affinity for the eluant.Thesuppressor increases the sensitivity of the method by bothincreasing the conductivity of the analytes and decreasing theconductivity of the eluant.The suppressor converts the eluantand the analytes to the corresponding hydrogen form acids.Ani
11、ons are quantitated by integration of their response com-pared with an external calibration curve and are reported asmilligrams per litre(mg/L).4.Significance and Use4.1 This test method provides for the qualitative and quan-titative determination of common anions in engine coolant inthe milligrams
12、per litre to low percent range and requires onlya few millilitres or microlitres of sample per test,with resultsavailable in less than 30 min.Acceptable levels of chloride andother anions vary with manufacturers blending specificationsand applicable ASTM minimum or maximum specifications.5.Interfere
13、nces5.1 Interferences can be caused by substances with similarretention times,especially if they are in high concentration1This test method is under the jurisdiction of ASTM Committee D15 on EngineCoolants and Related Fluids and is the direct responsibility of SubcommitteeD15.04 on Chemical Properti
14、es.Current edition approved June 1,2022.Published June 2022.Originallyapproved in 1995.Last previous edition approved in 2015 as D582709(2015).DOI:10.1520/D5827-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of
15、 ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard w
16、as developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1compared to those of the analyte of interest.Sample dilutionwill be used to minimize or solve most interference problems.5.2 A water dip(solvent system peak)can cause interfer-ence with some integrators.This is eli
