1、Designation:D5869/D5869M07a(Reapproved 2018)1Standard Practice forDark Oven Heat Exposure of Roofing and WaterproofingMaterials1This standard is issued under the fixed designation D5869/D5869M;the number immediately following the designation indicates theyear of original adoption or,in the case of r
2、evision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEUnits information was editorially corrected in January 2018.1.Scope1.1 This practice establishes a procedure
3、and conditions oftemperature and time for heat exposure of roofing and water-proofing materials and systems in the presence of air.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;theref
4、ore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to e
5、stablish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principle
6、s for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD1079 Terminology Relating to Roofing and WaterproofingD1566 Term
7、inology Relating to RubberE145 Specification for Gravity-Convection and Forced-Ventilation OvensE230/E230M Specification for Temperature-ElectromotiveForce(emf)Tables for Standardized ThermocouplesE1137/E1137M Specification for Industrial Platinum Resis-tance ThermometersE2251 Specification for Liqu
8、id-in-Glass ASTM Thermom-eters with Low-Hazard Precision Liquids3.Terminology3.1 DefinitionsFor definitions of terms used in thispractice,refer to Terminologies D883,D1079,and D1566.4.Summary of Practice4.1 Specimens of roofing and waterproofing materials areexposed to heat in a dark forced-ventilat
9、ion oven at a specifiedelevated temperature for a known period of time.4.2 This practice specifies an exposure temperature of 70 63C 158 6 5F in a forced-ventilation oven.4.3 This practice permits the selection of the duration ofheat exposure from three specified time periods,which are 35,90,and 180
10、 6 0.25 consecutive days.The duration selectedmust be included in any report of results obtained by using thispractice.NOTE1The time period to be used should be specified in any standardthat refers to this practice.European standards for polymer-modifiedbituminous materials specify 180 days at 70C.F
11、or research purposes,selection of other time periods and temperatures are permitted,providedthat the precise duration is stated in any report of results.4.4 This practice is also used to condition test specimens fortime periods much shorter than 35 days for the purpose ofconditioning material before
12、 testing.When used for thispurpose,the shorter conditioning time shall be specified in anyreport of test results.5.Significance and Use5.1 Roofing and waterproofing materials and systems un-dergo changes in physical properties as a result of beingsubjected to heat.They also undergo changes in physic
13、alproperties as they age in service.Since service conditions varywidely,any relationship between changes observed in thispractice and changes in service must be established by the userof this practice.1This practice is under the jurisdiction ofASTM Committee D08 on Roofing andWaterproofing and is th
14、e direct responsibility of Subcommittee D08.02 on SteepRoofing Products and Assemblies.Current edition approved Jan.1,2018.Published January 2018.Originallyapproved in 1995.Last previous edition approved in 2013 as D5869 07a(2013).DOI:10.1520/D5869_D5869M-07AR18E01.2For referenced ASTM standards,vis
15、it the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.Unite
16、d StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.Apparatus6.1 OvenThe oven shall have forced ventilation,shall beelectrically heated,and shall conform to the requirements ofSpecification E145,Type IIB.The oven shall be of s
