1、Designation:D505622Standard Test Method forTrace Metals in Petroleum Coke by Atomic Absorption1This standard is issued under the fixed designation D5056;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numb
2、er in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the analysis for the commonlydetermined trace metals(aluminum,calcium,iron,nickel,silicon,sodium,and vanadium)in labor
3、atory analysis samplesof raw and calcined petroleum coke by atomic absorptionspectroscopy.1.2 The elemental concentration ranges for which this testmethod is applicable and the limits of detection of this testmethod are listed in Table 1.1.3 The values stated in SI units are to be regarded as thesta
4、ndard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to us
5、e.For warning statements,see Sections 9 11.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the Wor
6、ld Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D346 Practice for Collection and Preparation of CokeSamples for Laboratory AnalysisD1193 Specification for Reagent WaterD4175 Terminology Relating to Petroleum Products,LiquidFuels,and Lubricants
7、D6299 Practice for Applying Statistical Quality Assuranceand Control Charting Techniques to Evaluate AnalyticalMeasurement System PerformanceD7740 Practice for Optimization,Calibration,and Valida-tion of Atomic Absorption Spectrometry for Metal Analy-sis of Petroleum Products and Lubricants3.Termino
8、logy3.1 Definitions:3.1.1 For definitions of terms used in this test method,referto Terminology D4175.4.Summary of Test Method4.1 A representative sample of the petroleum coke is ashedat 525 C under specified conditions.The ash is fused withlithium tetraborate(Li2B4O7),or lithium metaborate(LiBO3).T
9、he melt is dissolved in dilute hydrochloric acid(HCl),and theresultant solution is analyzed by atomic absorption spectros-copy for the following elements:aluminum,calcium,iron,nickel,silicon,sodium,and vanadium.4.2 Standard practice for using atomic absorption spectrom-etry for determination of meta
10、ls in petroleum products andlubricants can be found in Practice D7740.5.Significance and Use5.1 The presence and concentration of various metallicelements in a petroleum coke are major factors in the suitabilityof the coke for various uses.This test method provides a meansof measuring the amounts of
11、 those metallic elements in thecoke sample.5.2 The concentration of these elements is one factor indetermining the economic value of the coke.Coke used forproduction of electrodes will have different specification re-quirements dependent on what service the electrodes will beused in.Generally the fu
12、el cokes are highest in metallicelement concentration and have the least economic value.5.3 The test method provides a standard procedure for useby the purchaser and seller in the commercial transfer ofpetroleum coke to determine whether the lot of coke meets thespecifications of the purchasing part
13、y.6.Interferences6.1 Spectral interferences can occur when using other thanthe recommended wavelength for analysis or when usingmulti-elemental hollow cathode lamps.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricantsand is the direct res
14、ponsibility ofSubcommittee D02.03 on Elemental Analysis.Current edition approved Oct.1,2022.Published October 2022.Originallyapproved in 1990.Last previous edition approved in 2017 as D5056 17.DOI:10.1520/D5056-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Cust
15、omer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 194
16、28-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.17.Apparatus7.1 Furnace,electric,capable of regulation of temperatureat 525 C 6 10 C.7.2 Magnetic Stirring Hot Plate.7.3 Platinum Dish,50 mL to 58 mL capacity.7.4 Pl
