1、Designation:D541595(Reapproved 2020)Standard Test Method forEvaluating Load Containment Performance of Stretch WrapFilms by Vibration Testing1This standard is issued under the fixed designation D5415;the number immediately following the designation indicates the year oforiginal adoption or,in the ca
2、se of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method is used to evaluate and compare theability of stretch-wrap films to contain uni
3、tized loads duringshipping.1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory li
4、mitations prior to use.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organizatio
5、n TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D996 Terminology of Packaging and Distribution Environ-mentsD999 Test Methods for Vibration Testing of Shipping Con-tainers3.Terminology3.1 DefinitionsGeneral definitions for packaging and dis-tribution environments
6、 are found in Terminology D996.3.2 Definitions of Terms Specific to This Standard:3.2.1 amplitude,nthe maximum value of a sinusoidalquantity(zero to peak).3.2.2 resonance,na system of forced vibration existingwhen any change,however small,in the frequency of excita-tion causes a decrease in the resp
7、onse of the system.4.Significance and Use4.1 This test method is intended to be used mainly as ameans of comparing the performance of stretch-wrap films.Itcan also be used to compare the effectiveness of different wrapcycles with the same wrapping materials.No direct correlationbetween these test re
8、sults and actual field performance hasbeen established.4.2 This test method simulates the shipping of unitizedloads by way of truck and rail,concentrating on the vibrationelement associated with these modes.Other elements of thedistribution system,such as mechanical handling,are notaddressed specifi
9、cally in this test method.4.3 This test method establishes a method for rating theperformance of films,but it leaves open to the discretion of theuser the establishment of an acceptable rating for the specificend-use intended.5.Apparatus5.1 Load Wrapping ApparatusA machine or apparatus towrap the te
10、st load.The method of wrap application is prefer-ably as near as possible to that used in an actual productionsituation(stretch wrapper or manual wrapping unit).5.2 Vibration TableAvibration testing apparatus conform-ing to Test Methods D999,preferably equipped with thecapability of varying the freq
11、uency or amplitude,or both,ofvibration input in a controlled fashion and maintaining a setvibration mode.5.2.1 The table shall be large enough and have a weightcapacity sufficient to hold an entire wrapped shipping unit.5.2.2 The table should have a means for attaching thebottom of the wrapped test
12、unit securely to the table(forexample,threaded holes in the table surface for bolting a palletsecurely to the table).5.3 Accelerometer(optional),to measure the output re-sponse of the test load at various vibration table input frequen-cies.This is the most accurate way of determining the resonantfre
13、quency of the test load.6.Procedure6.1 Prepare the test load.Arrange the units comprising thetest load in layers and stack them in the manner normally usedfor shipping the product.1This test method is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcom
14、mittee D10.25 on Palletizingand Unitizing of Loads.Current edition approved Dec.15,2020.Published December 2020.Originallyapproved in 1993.Last previous edition approved in 2012 as D5415 95(2012).DOI:10.1520/D5415-95R20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact AST
15、M Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was develo
16、ped in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.16.2 When the units are normally shipped on pallets,stackthe units on the pallet in the normal manner.6.3 When the units are normally shipped on slip sheetswithout pallets,stack the units on slip sheets and affix thebottom l
