1、Designation:D531917An American National StandardStandard Specification forGlass-Fiber Reinforced Polyester Wall and Ceiling Panels1This standard is issued under the fixed designation D5319;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revis
2、ion,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers the classification,materials ofconstruction,workmanship,physical requirements,an
3、d meth-ods of testing glass-fiber-reinforced polyester composite walland ceiling panels intended for use in light construction andsemi-structural applications.1.2 Supplementary information on chemical resistance,im-pact resistance,and installation practice are provided in Ap-pendix X1.1.3 The classi
4、fication of these composite panels into classesbased on relative response to a laboratory test shall not beconsidered a fire-hazard classification.1.4 Laboratory flammability tests(Test Methods E84 andD1929)applicable to this specification should be used tomeasure and describe the properties of mate
5、rials,products,orassemblies in response to heat and flame under controlledlaboratory conditions and should not be used to describe orappraise the fire hazard or conditions.However,results may beused as elements of a fire risk assessment which takes intoaccount all of the factors which are pertinent
6、to an assessmentof the fire hazard of a particular end use.1.5 The intent of this specification is to define the class,grade,and general laminate properties of the composite walland ceiling liner panels in order to ensure a quality productwhich will perform in the intended application.This specifi-c
7、ation is not intended to restrict or limit technological changesaffecting performance when changes are agreed upon betweenthe purchaser and manufacturer.1.6 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are providedfor information only.1.7 Th
8、e text of this specification references notes andfootnotes that provide explanatory material.These notes andfootnotes(excluding those in Tables and Figures)shall not beconsidered as requirements of this specification.1.8 This standard does not purport to address all of thesafety concerns,if any,asso
9、ciated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health and environmental practices and deter-mine the applicability of regulatory limitations prior to use.NOTE1There is no known ISO equivalent to this standard.1.9 This international standard
10、was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced
11、 Documents2.1 ASTM Standards:2D374/D374M Test Methods for Thickness of Solid Electri-cal InsulationD618 Practice for Conditioning Plastics for TestingD883 Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1929 Test Method for Determining Ignition Temperatur
12、eof PlasticsD2244 Practice for Calculation of Color Tolerances andColor Differences from Instrumentally Measured ColorCoordinatesE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE631 Terminology of Building Constructions3.Terminology3.1 GeneralDefinitions are in accordance wit
13、h Terminolo-gies D883 and E631 and abbreviations with TerminologyD1600,unless otherwise indicated.3.2 Definitions of Terms Specific to This Standard:3.2.1 camber,nnon-linearity of the long axis of a panel.NOTE2In the process of water jet,knife,saw,or rotary sheartrimming of a continuous panel,sidewa
14、rds motion of the panel through the1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.24 on Plastic BuildingProducts.Current edition approved Sept.1,2017.Published September 2017.Originallyapproved in 1992.Last previous
15、 edition approved in 2012 as D5319 12.DOI:10.1520/D5319-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summ
16、ary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 cutting medium can
