1、Designation:D457422Standard Test Methods forRubber Compounding MaterialsDetermination of AshContent1This standard is issued under the fixed designation D4574;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A
2、 number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover the determination of ashcontent of rubber chemicals.1.2 The test methods include the following materials:Material
3、SectionSulfur7 13p-Phenylenediamine Antioxidants14 22Benzothiazole Sulfenamide Accel-erators14 221.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,a
4、ssociated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally re
5、cognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4483 Practice for Eva
6、luating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustriesD4676 Classification for Rubber Compounding MaterialsAntidegradants3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1“lot”samplea production sample representative of astandard producti
7、on unit,normally referred to as“the sample.”3.1.2 test unitthe actual material used in the analysis.Itmust be representative of the“lot”sample.4.Summary of Test Methods4.1 The ash content is determined by heating a knownquantity of the rubber chemical on a hot plate or over a gasburner to volatilize
8、 the sample and then heating in a mufflefurnace to complete the ashing process.4.2 Sample preparation,procedures,calculations,and pre-cision statements will be found in each section dealing with aparticular rubber chemical.5.Significance and Use5.1 These test methods are suitable for the determinati
9、on ofthe ash content of rubber compounding materials.The testmethods may be used for quality control,product acceptance,or research and development.Classification D4676 prescribespercent ash as an important characteristic of rubber antidegra-dants.6.Apparatus6.1 Muffle Furnace,capable of temperature
10、 regulation of625C between 500 and 800C.6.2 Hot Plate(or laboratory gas burner).6.3 Laboratory Fume Hood.6.4 Porcelain Combustion Crucible,capsule form,25-cm3capacity.6.5 Porcelain Crucible,high form,size 0,15-cm3capacity.6.6 Clay Triangle.6.7 Steel Crucible Tongs.6.8 Heat Resistant Gloves.6.9 Desic
11、cator.6.10 Analytical Balance,sensitive to 0.0001 g.6.11 Air Circulating Oven,capable of 70 6 2C.1These test methods are under the jurisdiction of ASTM Committee D11 onRubber and Rubber-like Materials and are the direct responsibility of SubcommitteeD11.11 on Chemical Analysis.Current edition approv
12、ed June 1,2022.Published June 2022.Originallyapproved in 1986.Last previous edition approved in 2021 as D4574 06(2021).DOI:10.1520/D4574-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume in
13、formation,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization
14、established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1SULFUR7.Scope7.1 This test method is used for the determination of the ashcontent of sulfur.7.2 This in
15、ternational standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)C
16、ommittee.8.Summary of Test Method8.1 The ash content of sulfur is determined by the controlledburning of the sulfur,followed by ashing in a furnace at 600C.9.Apparatus9.1 See Section 6.10.Procedure10.1 Weigh a 5-g specimen to the nearest 0.0001 g into apreviously ignited,weighed,25-cm3porcelain crucible.In awell-ventilated hood,place the crucible on a hot plate and heatto 400 to 500C,burning off most of the sulfur;or burn off thesulfur by moderate heating over a gas burner.When most of thesulfur
