1、Designation:D542619Standard Practices forVisual Inspection and Grading of Fabrics Used for InflatableRestraints1This standard is issued under the fixed designation D5426;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of las
2、t revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These practices cover procedures for the inspection andgrading of coated and uncoated woven flat and one-piecewoven(OPW)fabric
3、s,and for the inspection and culling of cutparts made of such fabrics,all of which are used in themanufacture of inflatable restraint cushions.1.2 For ease of reference,the scope,summary of practice,significance and use,apparatus,sampling,procedure,andreport sections are listed separately for each i
4、nspection prac-tice.Inspection PracticeSectionFabric Rolls7Cut Pieces&OPW81.3 These practices can be used to distinguish those fabricimperfections that may adversely affect inflatable restraintcushion fabrication or performance from those imperfectionsthat will not.1.4 Procedures and apparatus other
5、 than those stated inthese practices may be used by agreement of the purchaser andsupplier with the specific deviations from these practicesacknowledged in the report.1.5 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.6 This
6、standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.7 This inte
7、rnational standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Com
8、mittee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD6799 Terminology Relating to Inflatable Restraints2.2 ASTM Adjuncts:3Reference Photographs of Imperfections3.Terminology3.1 For all terminology relating to D13.20,Inflatablerestraints,refer to Terminology D6799.3.
9、1.1 The following terms are relevant to this standard:abrasion,air splice,bleedthrough,blip,broken filament,bruise,coating slub,coating streak,coating transfer,contamination,cushion,defect,filling bar,finished,foreign matter,grading,hard contamination,heavy coating streak,hole,imperfection,inflatabl
10、e restraint,inspection,light coating,light coatingstreak,longfloat,loop,majorimperfection,minorimperfection,missing coating,missing yarn,misweave,module,rework,sharp crease,short float,short knot,softcontamination,spit mark,stain,stitching,tight yarn,yarnstreak.3.2 For all other terms related to tex
11、tiles,see TerminologyD123.4.Summary of Practices4.1 Rolls of finished or coated fabric are examined forimperfections as the fabric traverses an inspection station.They are graded per Tables Tables 1-5.4.2 Cut pieces are inspected individually for imperfections.Cut pieces containing imperfections are
12、 culled from use forlater review.5.Significance and Use5.1 These practices are suitable for incorporation in aspecification.Any reference to material or cushion specifica-tion in these practices shall mean any similar agreement1These practices are under the jurisdiction ofASTM Committee D13 on Texti
13、lesand are the direct responsibility of Subcommittee D13.20 on Inflatable Restraints.Current edition approved Feb.1,2019.Published March 2019.Originallyapproved in 1993.Last previous edition approved in 2017 as D5426 12(2017).DOI:10.1520/D5426-19.2For referenced ASTM standards,visit the ASTM website
14、,www.astm.org,orcontact ASTM Customer Service ast serviceastm.org.For Annual Book of ASTMStandardsvolume information,refer to the standrds Document Summary page onthe ASTM website.3Available from:ASTM International Headquarters.Order Adjunct No.ADJD5426.Original adjunct produced in 1996.Copyright AS
15、TM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standard
16、s,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 between the purchaser and supplier relating to the inspectionand acceptance of fabric intended for inflatable restraint use.5.2 These practices constitute the terminology,conditions,equipment,and procedures by which rolls of inflatable restraintfabrics or cut parts are inspected and graded.5.3 A specification incorporating these practices may devi-ate from them to account for considera
