收藏 分享(赏)

ASTM_D_581_-_D_581M_-_12.pdf

上传人:益****师 文档编号:177014 上传时间:2023-03-04 格式:PDF 页数:6 大小:91.16KB
下载 相关 举报
ASTM_D_581_-_D_581M_-_12.pdf_第1页
第1页 / 共6页
ASTM_D_581_-_D_581M_-_12.pdf_第2页
第2页 / 共6页
ASTM_D_581_-_D_581M_-_12.pdf_第3页
第3页 / 共6页
ASTM_D_581_-_D_581M_-_12.pdf_第4页
第4页 / 共6页
ASTM_D_581_-_D_581M_-_12.pdf_第5页
第5页 / 共6页
ASTM_D_581_-_D_581M_-_12.pdf_第6页
第6页 / 共6页
亲,该文档总共6页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D581/D581M12Standard Specification forGlass Fiber Greige Braided Tubular Sleeving1This standard is issued under the fixed designation D581/D581M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A

2、number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the requirements for continu-ous glass filament greige braided tubular sleeving and issuitable for use as electr

3、ical insulation and for structural andmechanical applications.1.2 This specification is intended to assist ultimate users bydesignating the types of these products that are typical in theindustry.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.Th

4、e values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with

5、its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD350 Test Methods for Flexible Tre

6、ated Sleeving Used forElectrical InsulationD578 Specification for Glass Fiber StrandsD579 Specification for Greige Woven Glass FabricsD1059 Test Method for Yarn Number Based on Short-Length Specimens(Withdrawn 2010)3D1423 Test Method for Twist in Yarns by Direct-CountingD1776 Practice for Conditioni

7、ng and Testing TextilesD1907 Test Method for Linear Density of Yarn(Yarn Num-ber)by the Skein MethodD3773 Test Methods for Length of Woven FabricD3775 Test Method for Warp(End)and Filling(Pick)Countof Woven FabricsD4963 Test Method for Ignition Loss of Glass Strands andFabricsD7018 Terminology Relat

8、ing to Glass Fiber and Its Products2.2 ANSI Standard:ANSI/ASQC Z1.4 Sampling Procedures for Inspection byAttributes43.Terminology3.1 For all terminology related to D13.18,Glass Fiber andIts Products,see Terminology D7018.3.1.1 The following terms are relevant to this standard”braid,carrier,continuou

9、s filament yarn,greige goods,sleeving,and tubing.3.2 For all other terminology related to textiles,see Termi-nology D123.4.Tubing Classifications4.1 Glass fiber greige braided tubular sleeving is producedin one type and two styles within that type and uses yarnsdesignated as directed in Specificatio

10、n D578.The standardtype and styles are:4.1.1 Type GGlass fiber greige braided tubular sleeving.4.1.2 Style AGlass fiber greige braided tubular sleevinghaving a nominal wall thickness of 0.20 mm 0.008 in.4.1.3 Style BGlass fiber greige braided tubular sleevinghaving a nominal wall thickness of 0.15 m

11、m 0.006 in.REQUIREMENTS5.Material5.1 All yarns for braided tubular sleeving shall be electricalclassification,(E glass),continuous filament glass yarns,andshall fall within the chemical composition that is utilized for1This specification is under the jurisdiction of ASTM Committee D13 onTextiles and

12、 is the direct responsibility of Subcommittee D13.18 on Glass Fiber andits Products.Current edition approved July 1,2012.Published August 2012.Originallyapproved in 1940 T.Last previous edition approved in 2007 as D581 07.DOI:10.1520/D0581_D0581M-12.2For referenced ASTM standards,visit the ASTM webs

13、ite,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American Nationa

14、l Standards Institute,11 W.42nd St.,13thFloor,New York,NY 10036.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 general applications as described in Specification D578,Sec-tion 4.2.2.Filament size shall be agreed upon between pur-chaser a

15、nd supplier and shall meet the requirements of Speci-fication D578,Table 1 Letter Designations for Glass StrandFilament Diameters.5.1.1 The fiber shall be free of any free alkali metal oxides,such as soda or potash,and foreign particles,dirt,and otherimpurities.6.Yarn Number6.1 The nominal yarn numb

16、er of the yarns in the braidedtubular sleeving shall be agreed upon between the purchaserand the supplier.The average yarn number shall fall within theinterval:nominal yarn number6 10%of the nominal yarnnumber.7.Strand Construction7.1 The basis for specifying strand construction is given inSpecification D578.The construction of the component strandsshall be agreed upon between the purchaser and the supplier.8.Direction of Twist8.1 Unless otherwise agreed upon between the purchaserand the supplie

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2