收藏 分享(赏)

ASTM_D_5846_-_07_2012.pdf

上传人:益****师 文档编号:177062 上传时间:2023-03-04 格式:PDF 页数:6 大小:242.55KB
下载 相关 举报
ASTM_D_5846_-_07_2012.pdf_第1页
第1页 / 共6页
ASTM_D_5846_-_07_2012.pdf_第2页
第2页 / 共6页
ASTM_D_5846_-_07_2012.pdf_第3页
第3页 / 共6页
ASTM_D_5846_-_07_2012.pdf_第4页
第4页 / 共6页
ASTM_D_5846_-_07_2012.pdf_第5页
第5页 / 共6页
ASTM_D_5846_-_07_2012.pdf_第6页
第6页 / 共6页
亲,该文档总共6页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D584607(Reapproved 2012)Standard Test Method forUniversal Oxidation Test for Hydraulic and Turbine OilsUsing the Universal Oxidation Test Apparatus1This standard is issued under the fixed designation D5846;the number immediately following the designation indicates the year oforiginal ado

2、ption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a procedure for evaluating theoxidation stability of p

3、etroleum base hydraulic oils and oils forsteam and gas turbines.1.2 This test method was developed to evaluate the oxida-tion stability of petroleum base hydraulic oils and oils forsteam and gas turbines.1.2.1 Rust and oxidation inhibited hydraulic,anti-wear hy-draulic and turbine oils of ISO 3268 v

4、iscosity were used todevelop the precision statement.This test method has beenused to evaluate the oxidation stability of fluids made withsynthetic basestock and in-service oils;however,these fluidshave not been used in cooperative testing to develop precisiondata.1.3 The values stated in SI units a

5、re to be regarded asstandard.The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and d

6、etermine the applica-bility of regulatory limitations prior to use.Identified hazard-ous chemicals are listed in 7.3,7.6,and 7.8.Before using thistest method,refer to suppliers safety labels,Material SafetyData Sheets,and other technical literature.2.Referenced Documents2.1 ASTM Standards:2A510 Spec

7、ification for General Requirements for Wire Rodsand Coarse Round Wire,Carbon SteelB1 Specification for Hard-Drawn Copper WireD664 Test Method for Acid Number of Petroleum Productsby Potentiometric TitrationD943 Test Method for Oxidation Characteristics of InhibitedMineral OilsD974 Test Method for Ac

8、id and Base Number by Color-Indicator TitrationD3339 Test Method forAcid Number of Petroleum Productsby Semi-Micro Color Indicator TitrationD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4740 Test Method for Cleanliness and Compatibility ofResidual Fuels by Spot TestD4871 Guid

9、e for Universal Oxidation/Thermal StabilityTest ApparatusD5770 Test Method for Semiquantitative Micro Determina-tion of Acid Number of Lubricating Oils During Oxida-tion Testing2.2 Energy Institute Standard:3IP 2546Practice for Sampling of Petroleum Products;alternate to Practice D40572.3 British St

10、andard:4BS 1829 Specification for Carbon Steel Wire;alternate toSpecification A5102.4 ASTM Adjuncts:Reference Spot Sheet53.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 inhibited mineral oil,na petroleum oil containingadditives to retard oxidation.3.1.2 oxidation life,nof an oi

11、l,the time in hours requiredfor degradation of the oil under test.3.1.3 universal oxidation test,nthe apparatus and proce-dures described in Guide D4871.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of Subcommit

12、teeD02.09.0D on Oxidation of Lubricants.Current edition approved Dec.1,2012.Published December 2012.Originallyapproved in 1995.Last previous edition approved in 2007 as D584607.DOI:10.1520/D5846-07R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service

13、at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Energy Institute,61 New Cavendish St.,London,WIG 7AR,U.K.,http:/www.energyinst.org.uk.4Available from British Standards Institute(BSI),389 Chiswick H

14、igh Rd.,London W4 4AL,U.K.,http:/www.bsi-.5Available from ASTM International Headquarters.Order Adjunct No.ADJD4740.Original adjunct produced in 2000.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.Summary of Test Method4.1 An oil sampl

15、e is contacted with air at 135C in thepresence of copper and iron metals.The acid number and spotforming tendency of the oil are measured daily.The test isterminated when the oxidation life of the oil has been reached.4.2 The oil is considered to be degraded when either its acidnumber(measured by Te

16、st Methods D974 or D664)hasincreased by 0.5 mg KOH/g over that of new oil;or when theoil begins to form insoluble solids so that when a drop of oil isplaced onto a filter paper it shows a clearly defined dark spotsurrounded by a ring of clear oil.5.Significance and Use5.1 Degradation of hydraulic fluids and turbine oils,becauseof oxidation or thermal breakdown,can result in the formationof acids or insoluble solids and render the oil unfit for furtheruse.5.2 This test method can be used to estim

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2