1、Designation:D511397(Reapproved 2011)1Standard Test Method forDetermining Adhesive Attack on Rigid Cellular Foam1This standard is issued under the fixed designation D5113;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of las
2、t revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEUnits of measure were editorially changed from hard to soft conversions throughout the text in April 2011.1.Scope1.1 This test metho
3、d covers a practical means of measuringthe degree of rigid cellular polystyrene(RCPS)foam cavitationdamage when an adhesive is used to bond this substrate.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard doe
4、s not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standard
5、s:2C578 Specification for Rigid,Cellular Polystyrene ThermalInsulationD907 Terminology of Adhesives3.Terminology3.1 Definitions:3.1.1 Many terms in this standard are defined in Terminol-ogy D907.3.2 Definitions of Terms Specific to This Standard:3.2.1 cavitation damage,nas related to rigid cellularp
6、olystyrene foam,the pitting and wearing away of the surface.3.2.1.1 DiscussionDamage may include loss of material,surface deformation,or any other changes in microstructure,properties,or appearance.3.3 Abbreviations:3.3.1 RCPSRigid cellular polystyrene.4.Summary of Test Method4.1 This test method co
7、nsists of testing two RCPS sectionsbonded by adhesive and allowed to set for 24 h.Beforeevaluation,the degree of cavitation is measured and recorded.5.Significance and Use5.1 Rigid foam such as RCPS is used in the buildingconstruction industry.Because it is sensitive to certain compo-nents contained
8、 in adhesives which cause it to dissolve,it isimportant to have a test method to determine whether anadhesive is compatible with RCPS foam.This test methodwould help the end user decide which adhesive to use withRCPS foam by quantitatively measuring the amount of cavi-tation formed by the components
9、 contained in the adhesive.6.Apparatus6.1 Circular Template,with an inside diameter of 25 mm(1.0 in.)and a depth of 6 mm(14in.).6.2 Circulating Air Oven,for elevated temperature testing,capable of being held at 40 6 1C(104 6 2F).7.Materials7.1 For the test,use Type IV RCPS foam with a nominalthickne
10、ss of 25 mm(1.0 in.).7.2 If another type is used,record the type,thickness anddensity.8.Conditioning8.1 Unless otherwise agreed upon by the purchaser and themanufacturer,condition the test specimen and adhesive 24 hprior to testing at 23 6 1C(73 6 2F)and 50 6 5%relativehumidity.9.Procedure9.1 Prepar
11、e enough specimens so that two assemblies aretested at both temperatures.9.1.1 For each test,cut two sections of RCPS into 76 mm(3in.)by 76 mm(3 in.)specimens.9.1.2 Place the template in the center of one of the speci-mens.1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives
12、 and is the direct responsibility of Subcommittee D14.10 on WorkingProperties.Current edition approved April 1,2011.Published April 2011.Originallyapproved in 1997.Last previous edition approved in 2005 as D5113 97(2005).DOI:10.1520/D5113-97R11E01.2For referenced ASTM standards,visit the ASTM websit
13、e,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 9.1.3 Fi
14、ll the template with the desired adhesive,taking careto strike off any excess with a flat edge spatula.9.1.4 Immediately remove the template and superimposethe second piece of foamboard on top of the first one.Squeezethe assembly together until the adhesive can be seen squeezingout from between the
15、assembly.9.1.5 Wrap the assembly in a 305 mm(12.0 in.)by 305 mm(12.0 in.)piece of aluminum foil.9.2 Condition the assemblies for 24 h at the desired tem-peratures,room temperature and 40C(128F)or any otherrequested temperatures.9.3 After conditioning,unwrap the assemblies and cut themin half(corner
16、to corner to allow a greater cross-sectional area).9.4 Use a ruler to measure the maximum depth of thefoams cavitation to the nearest millimetre.Report cavitationas half the total depth of the two glued specimens.9.5 Record cavitation in millimetres(inches).10.Report10.1 Report the following information:10.1.1 Complete identification of the adhesive tested includ-ing type,source,manufacturers code number,date of test,dateof manufacture,etc.10.1.2 Temperature used for testing.10.1.3 Maximum depth
