收藏 分享(赏)

ASTM_D_4687_-_14_2022.pdf

上传人:益****师 文档编号:177598 上传时间:2023-03-04 格式:PDF 页数:8 大小:104.44KB
下载 相关 举报
ASTM_D_4687_-_14_2022.pdf_第1页
第1页 / 共8页
ASTM_D_4687_-_14_2022.pdf_第2页
第2页 / 共8页
ASTM_D_4687_-_14_2022.pdf_第3页
第3页 / 共8页
ASTM_D_4687_-_14_2022.pdf_第4页
第4页 / 共8页
ASTM_D_4687_-_14_2022.pdf_第5页
第5页 / 共8页
ASTM_D_4687_-_14_2022.pdf_第6页
第6页 / 共8页
亲,该文档总共8页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D468714(Reapproved 2022)Standard Guide forGeneral Planning of Waste Sampling1This standard is issued under the fixed designation D4687;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in

2、parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe analysis and testing of solid waste requires collection of adequately sized,representativesamples.Wastes are found in various locations and phys

3、ical states.Therefore,each sampling routineshall be tailored to fit the waste and situation.Wastes often occur as nonhomogeneous mixtures instratified layers or as poorly mixed conglomerations.For example,wastes are commonly stored ordisposed of in surface impoundments with stratified or layered slu

4、dges covered by ponded wastewater.In these situations,the collector may be faced with sampling the wastewater,the sludge,and somedepth of soil beneath the sludges.Collecting representative samples in these situations requires acarefully assessed,well-planned,and well-executed sampling routine.1.Scop

5、e1.1 This guide provides information for formulating andplanning the many aspects of waste sampling(see 1.2)that arecommon to most waste sampling situations.1.2 The aspects of sampling that this guide addresses are asfollows:SectionSafety plans4Sampling plans5Quality assurance considerations6General

6、 sampling considerations7Preservation and containerization8Cleaning equipment9Packaging,labeling,and shipping procedures10Chain-of-custody procedure111.3 This guide does not provide comprehensive samplingprocedures for these aspects,nor does it serve as a guide to anyspecific application.It is the r

7、esponsibility of the user to ensurethat the procedures used are proper and adequate.1.4 UnitsThe values stated in inch-pound units are to beregarded as the standard.The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered st

8、andard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to u

9、se.For more specific precautionary statements see 3.2,3.3,andSection 4.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-

10、mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2E122 Practice for Calculating Sample Size to Estimate,WithSpecified Precision,the Average for a Characteristic of aLot or Process2.2 Other Document:EPA-SW-846 Test Met

11、hods for Evaluating Solid Waste,Physical/Chemical Methods33.Significance and Use3.1 The procedures covered in this guide are general andprovide the user with information helpful for writing samplingplans,safety plans,labeling and shipping procedures,chain-of-custody procedures,general sampling proce

12、dures,generalcleaning procedures,and general preservation procedures.1This guide is under the jurisdiction of ASTM Committee D34 on WasteManagement and is the direct responsibility of Subcommittee D34.01.01 onPlanning for Sampling.Current edition approved May 1,2022.Published May 2022.Originallyappr

13、oved in 1987.Last previous edition approved in 2014 as D4687 14.DOI:10.1520/D4687-14R22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary pa

14、ge onthe ASTM website.3Available from Superintendent of Documents,U.S.Printing Office,Washington,DC 20402.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognize

15、d principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.2 For purposes of this guide,it is assumed that the user hasknowledge

16、 of the waste being sampled and the possible safetyhazards.3.3 This guide is not to be used when sampling sites orwastes when safety hazards are unknown.In such cases,theuser shall use other more appropriate procedures.4.Safety Plans4.1 Proper safety precautions shall always be observedwhen sampling wastes.Persons collecting samples shall beaware that the waste can be a strong sensitizer and corrosive,flammable,explosive,toxic,and capable of releasing ex-tremely poisonous gases.The background in

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2