1、Designation:D372090(Reapproved 2019)Standard Test Method forRatio of Anatase to Rutile in Titanium Dioxide Pigments byX-Ray Diffraction1This standard is issued under the fixed designation D3720;the number immediately following the designation indicates the year oforiginal adoption or,in the case of
2、revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the ratio ofanatase to rutile in titanium dioxide pigment
3、s.The method isalso applicable to pigment mixtures and pigmented coatingscontaining titanium dioxide.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if
4、any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with international
5、ly recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D215 Practice for
6、 the Chemical Analysis of White LinseedOil Paints(Withdrawn 2005)3D2371 Test Method for Pigment Content of Solvent-Reducible PaintsD2698 Test Method for Determination of the Pigment Con-tent of Solvent-Reducible Paints by High-Speed Centri-fugingD3925 Practice for Sampling Liquid Paints and RelatedP
7、igmented Coatings3.Summary of Test Method3.1 The X-ray diffraction pattern obtained from a material ischaracteristic of that material.The intensity of a diffractionpeak entirely due to one component of a mixture is dependentupon the amount of that substance in the mixture.To a minorextent the peak i
8、ntensity of the component is also dependent onthe mass absorption coefficient of other materials present.Since the test method utilizes the ratio of the intensities ofdiffraction peaks of two chemically similar materials,it isexpected that the effects of other constituents will be the samefor both m
9、aterials.3.2 The intensity of the diffraction maxima for anatase andrutile is measured by X-ray diffractometry.The intensity of theanatase peak is converted to anatase content relative to rutileand the rutile content is determined by difference.3.3 The X-ray diffraction measurement is made on single
10、pigments,pigment mixtures,films of pigmented coatings,andfilms prepared from liquid coatings,if interfering materials arenot present.When interfering materials are present,the pig-ment is separated from the redissolved(or ignited film,or fromthe liquid coating and treated to isolate the titanium dio
11、xide.4.Significance and Use4.1 This test method is used by titanium dioxide pigmentmanufacturers and users for process control and productacceptance.5.Interferences5.1 Calcium sulfate interferes,but its effect is eliminated bychemical removal(see Practice D215).It is desirable to assureby analysis t
12、hat any residual CaSO4is considerably less thanthe level of anatase being sought.The insoluble residue afterremoval of calcium sulfate should be ignited above 700C.Chrome yellow and the valentinite form of antimony trioxidealso interfere if not removed.High amounts of iron renderanalysis difficult d
13、ue to increased background(see Note 1).Additives,such as antimony and zinc,and impurities,such asniobium and zirconium,are generally present in solid solutionand thus would not have interfering diffraction peaks.Surfacetreatments such as silica and alumina do not interfere.Extreme1This test method i
14、s under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.31 on Pigment Specifications.Current edition approved May 1,2019.Published May 2019.Originallyapproved in 1978.Last previous edition approved in
15、2011 as D3720 90(2011).DOI:10.1520/D3720-90R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved
16、version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 differences
