1、Designation:D298322Standard Test Method forLow-Temperature Viscosity of Automatic TransmissionFluids,Hydraulic Fluids,and Lubricants using a RotationalViscometer1This standard is issued under the fixed designation D2983;the number immediately following the designation indicates the year oforiginal a
2、doption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.
3、Scope*1.1 This test method covers the use of rotational viscom-eters with an appropriate torque range and specific spindle forthe determination of the low-shear-rate viscosity of automatictransmission fluids,gear oils,hydraulic fluids,and somelubricants.This test method covers the viscosity range of
4、300 mPas to 900 000 mPas1.2 Thistestmethodwaspreviouslytitled“Low-Temperature Viscosity of Lubricants Measured by BrookfieldViscometer.”In the lubricant industry,D2983 test results haveoften been referred to as“Brookfield2Viscosity”which impliesa viscosity determined by this method.1.3 This test met
5、hod contains four procedures:Procedure Ais used when only an air bath is used to cool samples inpreparation for viscosity measurement.Procedure B is usedwhen a mechanically refrigerated programmable liquid bath isused to cool samples in preparation for viscosity measurement.Procedure C is used when
6、a mechanically refrigerated constanttemperature liquid bath is used to cool samples by means of asimulated air cell(SimAir)3Cell in preparation for viscositymeasurement.Procedure D automates the determination of lowtemperature,low-shear-rate viscosity by utilizing a thermo-electrically heated and co
7、oled temperature-controlled samplechamber along with a programmable rotational viscometer.1.4 There are multiple precision studies for this test method.1.4.1 The viscosity data used for the precision studies forProcedures A,B,and C covered a range from 300 mPas to170 000 mPas at test temperatures of
8、 12 C,26 C,and40 C.Appendix X5 includes precision data for 55 C testtemperature and includes samples with viscosities greater500 000 mPas.1.4.2 The viscosity data used for Procedure D precisionstudy was from 6400 mPas to 256 000 mPas at test tempera-tures of 26 C and 40 C.1.5 The values stated in SI
9、 units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5.1 The test method uses the SI unit,milliPascal-second(mPas),as the unit of viscosity.(1 cP=1 mPas).1.6 WARNINGMercury has been designated by manyregulatory agencies as a hazardous substance that can c
10、auseserious medical issues.Mercury,or its vapor,has been dem-onstrated to be hazardous to health and corrosive to materials.Use Caution when handling mercury and mercury-containingproducts.See the applicable product Safety Data Sheet(SDS)for additional information.The potential exists that sellingme
11、rcury or mercury-containing products,or both,is prohibitedby local or national law.Users must determine legality of salesin their location.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to es
12、tablish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles
13、 for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibili
14、ty ofSubcommittee D02.07 on Flow Properties.Current edition approved July 1,2022.Published August 2022.Originallyapproved in 1971.Last previous edition approved in 2021 as D2983 21.DOI:10.1520/D2983-22.2Brookfield viscometer and accessories are a trademark of AMETEKBrookfield,Inc,11CommerceBlvd.,Mid
15、dleboro,MA 02346,http:/.3SimAir is a trademark of Tannas Co.,4800 James Savage Rd.,Midland,MI48642,http:/.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international st
16、andard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.12.Referenced Documents2.1 ASTM Standards:4D341 Practice for Viscosity-Temperature Equations andCharts for Liquid Petroleum or Hydrocarbon ProductsD2162 Practice for Basic Calibration of Master Viscometersan
