收藏 分享(赏)

ASTM_D_3635_-_13.pdf

上传人:益****师 文档编号:179349 上传时间:2023-03-04 格式:PDF 页数:4 大小:74.60KB
下载 相关 举报
ASTM_D_3635_-_13.pdf_第1页
第1页 / 共4页
ASTM_D_3635_-_13.pdf_第2页
第2页 / 共4页
ASTM_D_3635_-_13.pdf_第3页
第3页 / 共4页
ASTM_D_3635_-_13.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D363513Standard Test Method forDissolved Copper In Electrical Insulating Oil By AtomicAbsorption Spectrophotometry1This standard is issued under the fixed designation D3635;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,

2、the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of copper innew or used electrical insulating oil of petroleum origin

3、 byatomic absorption spectrophotometry.1.2 The lowest limit of detectability is primarily dependentupon the method of atomization,but also upon the energysource,the fuel and oxidant,and the degree of electricalexpansion of the output signal.The lowest detectable concen-tration is usually considered

4、to be equal to twice the maximumvariation of the background.For flame atomization,the lowerlimit of detectability is generally in the order of 0.1 ppm or 0.1mg/kg.For non-flame atomization,the lower limit of detect-ability is less than 0.01 ppm.1.3 The values stated in SI units are to be regarded as

5、standard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the appl

6、ica-bility of regulatory limitations prior to use.See 5.4 for specificprecautionary statements.2.Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD3487 Specification for Mineral Insulating Oil Used inElectrical ApparatusD5222 Specification for High Fire-Point Mineral Elec

7、tricalInsulating Oils3.Summary of Test Method3.1 The test specimen of oil is filtered and diluted with anappropriate organic solvent and analyzed in an atomic absorp-tion spectrophotometer.Alternate procedures are provided forinstruments employing flame and non-flame atomization.Con-centration is de

8、termined by means of calibration curves pre-pared from standard samples.4.Significance and Use4.1 Electrical insulating oil may contain small amounts ofdissolved metals derived either directly from the base oil orfrom contact with metals during refining or service.Whencopper is present,it acts as a

9、catalyst in promoting oxidation ofthe oil.This test method is useful for research for new oils andto assess the condition of service-aged oils.Considerationshould be given to the limits of detection outlined in the scope.5.Apparatus5.1 Volumetric flasks,100-mL capacity.5.2 Membrane filter,0.45 m.5.3

10、 Burets,5 and 50-mL capacity.5.4 Atomic Absorption Spectrophotometer The instrumentshall have an atomizer,a spectral energy source,usuallyconsisting of a copper hollow cathode lamp,a monochromatorcapable of isolating the desired line of radiation,an adjustableslit,a photomultiplier tube or other pho

11、tosensitive device as alight measuring and amplifying device,and a read-out mecha-nism for indicating the amount of absorbed radiation.WarningProper ventilation must be provided to removetoxic metal vapors.5.4.1 Instruments employing flame atomization require anebulizer assembly,burner head,and suit

12、able pressure andflow regulating devices to maintain constant oxidant and fuelflow for the duration of the tests.5.4.1.1 Glass Syringe,10-mL capacity.5.4.2 Instruments employing non-flame atomization requirea suitable pressure regulating device to maintain an inertatmosphere.5.4.2.1 Graphite Furnace

13、 with background correction.5.4.2.2 Output Device,Printer or Strip Chart Recorder(ifpermanent record is required).1This test method is under the jurisdiction of ASTM Committee D27 onElectrical Insulating Liquids and Gases and is the direct responsibility of Subcom-mittee D27.03 on Analytical Tests.C

14、urrent edition approved May 1,2013.Published May 2013.Originallyapproved in 1977.Last previous edition approved in 2005 as D3635 01(2005).DOI:10.1520/D3635-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTM

15、Standards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.4.2.3 Pipets,1 and 5-L.5.5 Analytical Balance,capable of weighing to 0.0001 g.6.Reagents6.1 Pur

16、ity of ReagentsUse reagent grade chemicals in alltests.6.2 Purity of WaterUnless otherwise indicated,referencesto water shall be understood to mean reagent water conformingto the requirements in Specification D1193 for Reagent Water,Type 1.6.3 Nitric Acid(1:2)Add one volume of nitric acid(HNO3sp gr 1.42)to two volumes of water.6.4 New OilUnused oil of the same type as that beingtested,such as oil meeting the requirements of SpecificationD3487 or as described in Specification D5222.6.5 Methyl Iso

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2