1、Designation:D333307(Reapproved 2018)Standard Practice forSampling Manufactured Staple Fibers,Sliver,or Tow forTesting1This standard is issued under the fixed designation D3333;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year
2、of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers a procedure for the division ofshipments of manufactured staple fiber,sliver(or top)or towinto lots
3、 and the sampling of such lots for testing.NOTE1For sampling yarns,refer to Practice D2258.NOTE2This practice differs from BISFA2rules for staple fibers in thelot sampling,by the elimination of separate sampling of outer versus innercontainer areas,in the reduction of number of strata from 6 to 5,an
4、d bythe elimination of compositing to obtain a single laboratory sample for thelot when testing properties which do not depend on as-received moisturecontent.1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of
5、this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Dec
6、ision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D123 Terminology Relating to TextilesD2258 Practice for Sampling Yarn for TestingD42
7、71 Practice for Writing Statements on Sampling in TestMethods for Textiles(Withdrawn 2009)4D4849 Terminology Related to Yarns and Fibers3.Terminology3.1 For all terminology relating to D13.58,Yarns andFibers,refer to Terminology D4849.3.2 For all other terminology related to textiles,refer toTermino
8、logy D123.4.Summary of Practice4.1 Instructions are given for dividing containers into lots,for determining the number of containers to be selected fromeach lot as the lot sample,and for determining the number ofcontainers taken from the lot sample as a laboratory sample.See Practice D4271.4.2 Separ
9、ate laboratory samples are taken for commercialweight measurement and for other testing,for example,physi-cal or chemical tests.4.3 The manner of preparing laboratory sampling units forcommercial weight,and the manner of collecting laboratorysampling units for other testing are based on the followin
10、g:4.3.1 Present knowledge of the systematic variation ofmoisture within the container,and4.3.2 The variability of the properties for which the practiceis to be used.5.Significance and Use5.1 Assigning a value to any property of the material in acontainer or in a lot,consignment,or delivery involves
11、ameasurement process that includes both sampling and testingprocedures.The correctness of the value assigned dependsupon the variability due to testing.Even when the variabilitydue to testing is minimized by carefully developed procedures,correct and consistent estimates of the true value of theprop
12、erty are possible only when the sampling procedure avoidssystematic bias,minimizes variations due to sampling,andprovides a laboratory sample of adequate size.1This practice is under the jurisdiction ofASTM Committee D13 on Textiles andis the direct responsibility of Subcommittee D13.58 on Yarns and
13、 Fibers.Current edition approved July 1,2018.Published August 2018.Originallyapproved in 1974.Last previous edition approved in 2012 as D3333 07(2012).DOI:10.1520/D3333-07R18.2BISFA Internationally Agreed Methods for Testing Polyamide Staple Fibers,1974 edition,BISFA Internationally Agreed Methods f
14、or Testing Polyester StapleFibers,1972 edition,and BISFA Rules for Testing Regenerated Cellulose andAcetate Staple Fibers,1970 edition,available from the Bureau International pour laStandardisation de la Rayonne et des Fibres Synthetiques.3For referenced ASTM standards,visit the ASTM website,www.ast
15、m.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbo
16、r Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.2 This practice may not give the most efficient samplingplan that might be devised in special situations but it doesp
