1、Designation:D335922Standard Test Methods forRating Adhesion by Tape Test1This standard is issued under the fixed designation D3359;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indi
2、cates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover procedures for assessing theadhesion of relatively ductile coating films to metallic sub-strates by applying and removing pressure-sensitive
3、 tape overcuts made in the film.1.2 Test Method A is primarily intended for use in the fieldwhile Test Method B is more suitable for use in laboratory orshop environments.Also,Test Method B is not consideredsuitable for films thicker than 125 m(5 mils)unless widerspaced cuts are employed and there i
4、s an explicit agreementbetween the purchaser and seller.1.3 These test methods are used to evaluate whether theadhesion of a coating to a substrate is adequate for the usersapplication.They do not distinguish between higher levels ofadhesion for which more sophisticated methods of measure-ment are r
5、equired.1.4 This test method is similar in content(but not techni-cally equivalent)to ISO 2409.1.5 In multicoat systems adhesion failure may occur be-tween coats so that the adhesion of the coating system to thesubstrate is not determined.1.6 The values stated in SI units are to be regarded as thest
6、andard.The values given in parentheses are for informationonly.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-min
7、e the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations i
8、ssued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D609 Practice for Preparation of Cold-Rolled Steel Panelsfor Testing Paint,Varnish,Conversion Coatings,andRelated Coating ProductsD823 Practices for Producing Films of Uniform Thi
9、cknessof Paint,Coatings and Related Products on Test PanelsD1000 Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applica-tionsD1730 PracticesforPreparationof AluminumandAluminum-Alloy Surfaces for PaintingD2092 Guide for Preparation of Zinc-Coated(Galvani
10、zed)Steel Surfaces for Painting(Withdrawn 2008)3D2370 Test Method for Tensile Properties of Organic Coat-ingsD3330/D3330M Test Method for PeelAdhesion of Pressure-Sensitive TapeD3924 Specification for Standard Environment for Condi-tioning and Testing Paint,Varnish,Lacquer,and RelatedMaterialsD4060
11、Test Method for Abrasion Resistance of OrganicCoatings by the Taber Abraser2.2 Other Standards:ISO 2409 Paint and Varnishes Cross-cut test4PSTC 101 International Standard for Peel Adhesion ofPressure Sensitive Tape53.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 adhesion,nthe m
12、olecular attraction and mechanicalbonds between a coating and its substrate.3.1.2 batch,nas it pertains to tape,a unique productionrun during manufacturing.1These test methods are under the jurisdiction of ASTM Committee D01 onPaint and Related Coatings,Materials,and Applications and are the directr
13、esponsibility of Subcommittee D01.23 on Physical Properties of Applied PaintFilms.Current edition approved July 1,2022.Published July 2022.Originally approvedin 1974.Last previous edition approved in 2017 as D3359 17.DOI:10.1520/D3359-22.2For referenced ASTM standards,visit the ASTM website,www.astm
14、.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards
15、Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.5Available from the Pressure Sensitive Tape Council(PSTC),1833 Centre PointCircle,Suite 123,Naperville,IL 60563,http:/www.pstc.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-29
16、59.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.1.3 blemish,nan obvious surface flaw,such as crackingor discoloration of the coating.3.1.4 environmental conditions,nthe characteristics of theimmediate surroundings d
