1、Designation:D379017Standard Test Method forVolatile Matter(Moisture)of Leather by Oven Drying1This standard is issued under the fixed designation D3790;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numbe
2、r in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers the determination of volatilematter
3、(moisture)in all types of leather.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of t
4、his standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Princi
5、ples for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D2813 Practice for Sampling Leather for Physical andChemical Tests3.Summary of Test Method3.1 The g
6、round leather specimen is heated in a mechanical-convection oven for 16 h at 100C,placed in a desiccator,cooled,and reweighed.The loss in weight represents thevolatile matter.4.Significance and Use4.1 The result obtained by this test is normally considered tobe the moisture content of the leather sa
7、mple.This result isused to correct all other chemical tests to a moisture-free basis.4.2 Materials that are volatile under these conditions,otherthan water,may be present in the leather,although their amountin any normal leather would be expected to be a very smallpercentage of the total volatile ma
8、tter.4.3 Under the conditions of this test,certain materials inleather,such as protein fiber and chromium tanning salts,mayretain moisture.Other materials,such as tannins and oils,maybe oxidized.Both of these effects produce negative errors inthe moisture determination.4.4 The amount of volatile mat
9、ter(moisture)released by agiven leather varies with(a)degree of grinding of the sample,(b)weight of sample taken,(c)temperature and time of theoven drying,(d)shape of the weighing container,and(e)typeof oven(gravity versus mechanical convection)used.4.5 Because of the above unknown errors,the result
10、 of thistest is a purely arbitrary value for the moisture content of thesample.It is,therefore,essential that the method be followedexactly in order to obtain reproducible results among labora-tories.This is particularly true if other chemical analytical testsbeing performed on the same sample are r
11、eported on themoisture-free basis.5.Apparatus5.1 Weighing Bottle3,glass,low-form,cylindrical with aground-glass stopper of standard taper.The bottle shall have 706 5 mm inside diameter,and 33 6 3 mm overall height.5.2 Oven,mechanical-convection draft capable of setting at100 C,with a thermoregulator
12、 system capable of holding oventemperature within 62 C of set point.Athermometer accurateto 60.2 C should be used to check and monitor the oven setpoint.5.3 Balance,capable of weighing up to 100 g with anaccuracy of 60.001 g.5.4 Desiccator,any convenient form or size,using anynormal desiccating agen
13、t such as calcium sulfate,calciumchloride,or silica gel.1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.06 on Chemical Analysis.Current edition approved April 1,2017.Published May 2017.Originallyapproved in 1979.Last pr
14、evious edition approved in 2012 as D3790-79(2012).DOI:10.1520/D3790-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM web
15、site.3Weighing bottles that have been found to be satisfactory are the Kimble GlassCo.No.15165 with 71/15 standard-taper caps and are available from mostlaboratory supply houses.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis internati
16、onal standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.Sampling6.1 The leather shall be sampled in accordance with PracticeD2813.7.Procedure7.1 Insert the empty weighing bottle inside the invertedstoppered cap and place on a shelf in the oven at 100 6
