1、Designation:D266514Standard Specification forPoly(Vinyl Chloride)(PVC)Plastic Drain,Waste,and VentPipe and Fittings1This standard is issued under the fixed designation D2665;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of
2、 last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers requiremen
3、ts and test methodsfor materials,dimensions and tolerances,pipe stiffness,crushresistance,impact resistance,and solvent cement for poly(vinylchloride)plastic drain,waste,and vent pipe and fittings.Aformof marking is also included.Plastic which does not meet thematerial requirements specified in Sect
4、ion 5 is excluded.Installation procedures are given in the Appendix.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The text of th
5、is specification references notes,footnotes,and appendixes which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.4 The following safety hazards caveat pertains only to thetest methods portion,Se
6、ction 7,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior t
7、o use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Det
8、ermining Dimensions of Ther-moplastic Pipe and FittingsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D256
9、4 Specification for Solvent Cements for Poly(VinylChloride)(PVC)Plastic Piping SystemsD3311 Specification for Drain,Waste,and Vent(DWV)Plastic Fittings PatternsF402 Practice for Safe Handling of Solvent Cements,Primers,and Cleaners Used for Joining ThermoplasticPipe and FittingsF412 Terminology Rela
10、ting to Plastic Piping SystemsF1498 Specification for Taper Pipe Threads 60 for Thermo-plastic Pipe and FittingsF1866 Specification for Poly(Vinyl Chloride)(PVC)PlasticSchedule 40 Drainage and DWV Fabricated FittingsF2135 Specification for Molded Drain,Waste,and Vent(DWV)Short-Pattern Plastic Fittin
11、gs3.Terminology3.1 Definitions are in accordance with Terminology F412,and abbreviations are in accordance with Terminology D1600,unless otherwise specified.4.Significance and Use4.1 The requirements of this specification are intended toprovide pipe and fittings suitable for the drainage and venting
12、of sewage and certain other liquid wastes.NOTE1Industrial waste disposal lines should be installed only withthe specific approval of the cognizant building code authority sincechemicals not commonly found in drains and sewers and temperatures inexcess of 180F(82.2C)may be encountered.NOTE2This speci
13、fication does not include requirements for pipe andfittings intended to be used to vent combustion gases.5.Materials5.1 Basic MaterialsThe pipe shall be made of virgin PVCcompounds meeting or exceeding the requirements of Class1This specification is under the jurisdiction of ASTM Committee F17 on Pl
14、asticPiping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved May 1,2014.Published June 2014.Originallyapproved in 1968.Last previous edition approved in 2012 as D2665 12.DOI:10.1520/D2665-14.2For referenced ASTM standards,visit the ASTM website,www.astm
15、.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,
16、West Conshohocken,PA 19428-2959.United States1 12454 as defined in Specification D1784.The fittings shall bemade of virgin PVC compounds meeting or exceeding therequirements of Class 12344 as defined in SpecificationD1784,but with a tensile strength of not less than 6500 psi anda modulus of elasticity for not less than 380,000 psi.Theseplastics contain stabilizers,lubricants,and pigments.5.2 Rework MaterialThe manufacturer shall use only hisown clean pipe or fitting rework material,and the pipe
