1、Designation:D291707(Reapproved 2013)Standard Specification forMethyl Isoamyl Ketone1This standard is issued under the fixed designation D2917;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in paren
2、theses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers methyl isoamyl ketone(98%grade)for use in paint,varnish,lacquer,and related products.1.2 The following applies to all specified
3、limits in thisstandard:for purposes of determining conformance with thisstandard,an observed value or a calculated value shall berounded off“to the nearest unit”in the last right-hand digitused in expressing the specification limit,in accordance withthe rounding-off method of Practice E29.1.3 The va
4、lues stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.4 For specific hazard information and guidance,see thesuppliers Material Safety Data Sheet.2.Referenced Documents2.1 ASTM Standards:2D268 Guide for Sampling and Testing Volatile Solvent
5、s andChemical Intermediates for Use in Paint and RelatedCoatings and MaterialD1078 Test Method for Distillation Range of Volatile Or-ganic LiquidsD1209 Test Method for Color of Clear Liquids(Platinum-Cobalt Scale)D1364 Test Method for Water in Volatile Solvents(KarlFischer Reagent Titration Method)D
6、1476 Test Method for Heptane Miscibility of LacquerSolventsD1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint,Varnish,Lacquer,and Related ProductsD3893 Test Method for Purity of Methyl Amyl Ketone andMethyl Isoamyl Ketone by Gas ChromatographyD4052 Test Method
7、 for Density,Relative Density,and APIGravity of Liquids by Digital Density MeterD5386 Test Method for Color of Liquids Using TristimulusColorimetryE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE300 Practice for Sampling Industrial Chemicals2.2 U.S.
8、Federal Specification:PPP-C-2020 Chemicals,Liquid,Dry,and Paste:Packagingof33.Properties3.1 Methyl isoamyl ketone shall conform to the followingrequirements:Apparent specific gravity:20/20C0.812 to 0.815or25/25C0.809 to 0.812Color,Pt-Co scale,max(Note 1)15Distillation,CInitial boiling point,min140Dr
9、y point,max148Water,wt%,max0.1Acidity as acetic acid,wt%,max0.02Purity,wt%,min98_NOTE1Instrumental Pt-Co color determined by Test Method D5386has been shown to have no statistically significant difference from Pt-Cocolor determined by Test Method D1209.However,it is not knownwhether methyl isoamyl k
10、etone was part of the sample set included in theinterlaboratory study.4.Sampling4.1 The material shall be sampled in accordance withPractice E300.5.Test Methods5.1 The properties enumerated in this specification shall bedetermined in accordance with the following ASTM testmethods:5.1.1 Apparent Spec
11、ific GravityDetermine the apparentspecific gravity by any convenient method that is accurate to1This specification is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.35 on Solvents,Plasticizers,a
12、nd Chemical Intermediates.Current edition approved June 1,2013.Published June 2013.Originallyapproved in 1970.Last previous edition approved in 2007 as D2917 07.DOI:10.1520/D2917-07R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.o
13、rg.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/www.dodssp.daps.mil.Copyright ASTM International,100 Barr
14、Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 the third decimal place,the temperature of both specimen andwater being 20C or 25C.See Guide D268 or Test MethodD4052.5.1.2 ColorTest Method D1209(see Note 1).5.1.3 Distillation RangeTest Method D1078,using a tem-perature measur
15、ing device having a range of 98 to 152C anda resolution of 0.1C.5.1.4 WaterTest Method D1364.45.1.5 AcidityTest Method D1613.5.1.6 PurityTest Method D3893.6.Packaging and Package Marking6.1 Package size shall be agreed upon by the purchaser andthe supplier.6.2 Packaging shall conform to applicable c
16、arrier rules andregulations or when specified shall conform to Fed.Spec.PPP-C-2020.7.Keywords7.1 ketone;methyl isoamyl ketone;MIAK;solventsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to r
