收藏 分享(赏)

ASTM_D_380_-_94_2012.pdf

上传人:益****师 文档编号:181940 上传时间:2023-03-04 格式:PDF 页数:10 大小:180.67KB
下载 相关 举报
ASTM_D_380_-_94_2012.pdf_第1页
第1页 / 共10页
ASTM_D_380_-_94_2012.pdf_第2页
第2页 / 共10页
ASTM_D_380_-_94_2012.pdf_第3页
第3页 / 共10页
ASTM_D_380_-_94_2012.pdf_第4页
第4页 / 共10页
ASTM_D_380_-_94_2012.pdf_第5页
第5页 / 共10页
ASTM_D_380_-_94_2012.pdf_第6页
第6页 / 共10页
亲,该文档总共10页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D38094(Reapproved 2012)Standard Test Methods forRubber Hose1This standard is issued under the fixed designation D380;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indica

2、tes the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.These methods have been approved for use byagencies of the Department of Defense to replace Metho

3、ds 7431,7421,10011,10021,10211,10221,10311,10341,10351,and10361 of Federal Test Method Standard No.601 and for listing in the DoD Index of Specifications and Standards.1.Scope1.1 These test methods cover procedures for inspection andtest of all types and constructions of rubber hose.21.2 In case of

4、conflict between provisions of these testmethods and those of detailed specifications or test methods fora particular hose,the latter shall take precedence.1.3 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.4 This standard do

5、es not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standar

6、ds:3D412 Test Methods for Vulcanized Rubber and Thermoplas-tic ElastomersTensionD413 Test Methods for Rubber PropertyAdhesion to Flex-ible SubstrateD471 Test Method for Rubber PropertyEffect of LiquidsD572 Test Method for RubberDeterioration by Heat andOxygenD573 Test Method for RubberDeterioration

7、in an AirOvenD865 Test Method for RubberDeterioration by Heating inAir(Test Tube Enclosure)D1149 Test Methods for Rubber DeteriorationCracking inan Ozone Controlled EnvironmentD1415 Test Method for Rubber PropertyInternationalHardnessD2240 Test Method for Rubber PropertyDurometer Hard-nessD3183 Prac

8、tice for RubberPreparation of Pieces for TestPurposes from ProductsD3767 Practice for RubberMeasurement of DimensionsD4483 Practice for Evaluating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustriesE4 Practices for Force Verification of Testing Machines3.General

9、 Test Methods3.1 Except as otherwise specified in these test methods forrubber hose,the following test methods,applicable in generalto vulcanized rubber,shall be complied with as required andare hereby made a part of these test methods:3.1.1 General Physical Test RequirementsPractice D3183.3.1.2 Ten

10、sion TestTest Methods D412.3.1.3 Aging TestTest Method D572,Test Method D573,and Test Method D865.3.1.4 Adhesion TestTest Methods D413.3.1.5 Immersion TestTest Method D471.3.1.6 Hardness TestTest Method D2240.3.1.7 Hardness TestTest Method D1415.4.Significance and Use4.1 These test methods provide u

11、niform methods for inspec-tion and test of rubber hoses that can be referenced in hosespecifications for various applications.1These test methods are under the jurisdiction of ASTM Committee D11 onRubber and are the direct responsibility of Subcommittee D11.31 on Rubber Hoseand Belting.Current editi

12、on approved May 1,2012.Published July 2012.Originally approvedin 1933.Last previous edition approved in 2006 as D380 94(2006).DOI:10.1520/D0380-94R12.2For specifications covering hose used in automotive,construction,and indus-trial equipment applications,reference should be made to SAE Standards for

13、Coolant System Hoses(SAE J20e),Fuel and Oil Hoses(SAE J30b),Power SteeringPressure HoseHigh Volumetric Expansion(SAE J188),Power Steering ReturnHose(SAE 189),Power Steering Pressure HoseLow Volumetric Expansion(SAEJ191),Power Steering Pressure HoseWire Braid(SAE J190),Windshield WiperHose(SAE J50a),

14、Emission Control Hose(SAE J1010),Windshield Washer Tubing(SAE J1037),Tests and Procedures for SAE 100R Series Hydraulic Hose and HoseAssemblies(SAE J343c),and for Tests and Procedures for High-TemperatureTransmission Oil Hose,Lubricating Oil Hose,and Hose Assemblies(SAE J1019).3For referenced ASTM s

15、tandards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 1942

16、8-2959.United States1 4.2 Uniform test methods make quality comparisons of hoseeasier and more meaningful,and are more economical particu-larly when the same rubber vulcanizates are used in differenttypes,constructions,or sizes of hose.5.Sampling5.1 A sample of sufficient length for proper performance ofthe required tests shall be cut from the hose when possiblewithout impairing its use and the pieces of hose from whichsamples have thus been cut shall be accepted by the purchaseras full length,p

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2