收藏 分享(赏)

ASTM_D_1603_-_20.pdf

上传人:益****师 文档编号:182383 上传时间:2023-03-04 格式:PDF 页数:4 大小:129.40KB
下载 相关 举报
ASTM_D_1603_-_20.pdf_第1页
第1页 / 共4页
ASTM_D_1603_-_20.pdf_第2页
第2页 / 共4页
ASTM_D_1603_-_20.pdf_第3页
第3页 / 共4页
ASTM_D_1603_-_20.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D160320Standard Test Method forCarbon Black Content in Olefin Plastics1This standard is issued under the fixed designation D1603;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parent

2、heses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method covers the determination of the carbonblack content

3、in polyethylene,polypropylene,and polybuty-lene plastics.Its use with acrylic or other polar monomermodifications which might affect the accuracy is not recom-mended.Determinations of carbon black content are madegravimetrically after pyrolysis of the sample under nitrogen.This test method is not ap

4、plicable to compositions that containnonvolatile pigments or fillers other than carbon black.1.1.1 This test method is not applicable to materials con-taining brominated flame retardant additives at the end.1.2 The values stated in SI units are to be regarded asstandard.The values in parentheses are

5、 given for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory li

6、mitations prior to use.NOTE1This standard and ISO 6964-1986(E)address the same subjectmatter,but differ in technical content.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDe

7、velopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD4218 Test Method for Determination of Carbon BlackContent in Polyethylene C

8、ompounds By the Muffle-Furnace TechniqueE456 Terminology Relating to Quality and StatisticsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test MethodE2935 Practice for Conducting Equivalence Testing inLaboratory Applications2.2 ISO Standard:ISO6964-1986(E)Polyol

9、efinPipesandFittingsDetermination of Carbon Black by Calcination andPyrolysisTest Method and Basic Specification33.Terminology3.1 Terms used in this standard are defined in accordancewith Terminology D883,unless otherwise specified.For termsrelating to precision and bias and associated issues,the te

10、rmsused in this standard are defined in accordance with Terminol-ogy E456.4.Significance and Use4.1 The information provided by this test method is usefulfor manufacturing quality control,technical service,and re-search purposes;and is required by various material specifica-tions and for the calcula

11、tion of optical absorptivity.4.2 Test Method D4218 is available for determining thecarbon black content of polyethylene compounds if so desired.5.Apparatus5.1 Electric Furnace,at least 20 cm(7.9 in.)long suitablefor use with the tubing described in 5.2.5.2 High Temperature Glass Combustion Tube4,of

12、appro-priate diameter and approximately twice as long as the furnacedescribed in 5.1.5.3 StoppersTwo rubber or neoprene stoppers,to fit thetube described in 5.2,unless the tube is fitted with groundjoints and mating connectors.1This test method is under the jurisdiction of ASTM Committee D20 on Plas

13、ticsand is the direct responsibility of Subcommittee D20.70 on Analytical Methods(Section D20.70.01).Current edition approved Feb.1,2020.Published March 2020.Originallyapproved in 1958.Last previous edition approved in 2014 as D1603-14.DOI:10.1520/D1603-20.2For referenced ASTM standards,visit the AS

14、TM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3ISO/IEC Selected Standards for Testing Plastics,Second Edition,published byASTM.Also available from American

15、 National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036.4Borosilicate,high-silica,or equivalent glass tubing has been found satisfactoryfor this purpose.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C7

16、00,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.5.4 Glass Tubing,approximately 10 mm(0.39 in.)indiameter,of sufficient amount,and matching rubber or plastictubing for connections.5.5 Com

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2