1、Designation:D 1249 92(Reapproved 1999)Standard Specification forOctyl Ortho-Phthalate Ester Plasticizers1This standard is issued under the fixed designation D 1249;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi
2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers octyl orthophthalate ester plas-ticizers,suitable for use in the compounding of plastics.NOTE1There are n
3、o ISO standards covering the primary subject ofthis specification.NOTE2The properties included in this specification are those re-quired to identify the type of plasticizer covered.There may be otherrequirements necessary to identify particular characteristics.These will beadded to this specificatio
4、n as their inclusion becomes desirable and thenecessary test data and methods become available.1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health pract
5、ices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:D 883 Terminology Relating to Plastics2D 1045 Methods of Sampling and Testing Plasticizers Usedin Plastics2D 1600 Terminology for Abbreviated Terms Relating toPlastics2D 3892 Practic
6、e for Packaging/Packing of Plastics3E 203 Test Method for Water Using Karl Fischer Reagent43.Terminology3.1 GeneralDefinitions are in accordance with Terminol-ogy D 883 and abbreviations with Terminology D 1600,unlessotherwise indicated.4.Classification4.1 This specification covers two types of octy
7、l ortho-phthalate ester plasticizers:4.1.1 Type I,2-ethyl hexyl phthalate ester,and4.1.2 Type II,mixed isooctyl phthalate ester.5.Chemical Requirements5.1 The plasticizer shall conform to the requirements pre-scribed in Table 1.6.Physical Requirements6.1 The plasticizer shall be substantially free o
8、f suspendedmatter.6.2 The odor of the plasticizer shall be mild.7.Sampling and Test Methods7.1 Sample and test the plasticizer in accordance withMethods D 1045 and determine moisture in accordance withTest Method E 203.8.Retest and Rejection8.1 If any failure occurs,the materials may be retested toe
9、stablish conformity in accordance with agreement betweenthe purchaser and the seller.9.Packaging and Package Marking9.1 PackagingThe material shall be packaged in standardcommercial containers,so constructed as to ensure acceptanceby common or other carriers for safe transportation at thelowest rate
10、 to the point of delivery,unless otherwise specifiedin the contract or order.9.2 Package MarkingShipping containers shall bemarked with the name of the material,type,and the quantitycontained therein,as defined by the contract or order underwhich shipment is made,the name of the manufacturer,and the
11、number of the contract or order.9.3 All packing,packaging,and marking provisions ofPractice D 3892 shall apply to this specification.10.Keywords10.1 octyl-ortho-phthalate ester;plasticizers1This specification is under the jurisdiction of ASTM Committee D-20 onPlastics and is the direct responsibilit
12、y of Subcommittee D20.15 on ThermoplasticMaterials(Section D20.15.07).Current edition approved Oct.15,1992.Published December 1992.Originallypublished as D 1249 54.Last previous edition D 1249 81(1988).2Annual Book of ASTM Standards,Vol 08.01.3Annual Book of ASTM Standards,Vol 08.02.4Annual Book of
13、ASTM Standards,Vol 15.05.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standa
14、rd are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif n
15、ot revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you
16、 may attend.If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,at the address shown below.This standard is copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints(single or multiple copies)of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585(phone),610-832-9555(fax),or serviceastm.org(e-mail);or through
