1、Designation:D228411(Reapproved 2019)Standard Test Method forAcidity of Sulfur Hexafluoride1This standard is issued under the fixed designation D2284;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number i
2、n parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the acidicfluorides of sulfur hexafluoride(SF6).1.2 The values stated in SI units are to be regarded a
3、sstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and det
4、er-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendat
5、ions issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent Water3.Summary of Test Method3.1 Acidic constituents of the sample are absorbed inslightly alkaline water containing an indicator and the exc
6、essbase titrated with a standard acid solution.The resultant acidityis expressed as equivalents of hydrofluoric acid(HF).4.Significance and Use4.1 Acidic fluorides are undesirable in SF6used as anelectrical insulating gas in that they may contribute to corro-sion or constitute dielectric hazard.4.2
7、This test method is valid for both new and used SF6.Inused SF6,it will only measure those active species which arehydrolyzable.5.Apparatus5.1 Gas Washing Bottles,500-mL capacity,two required.5.2 Microburet,graduated to 0.01 mL.5.3 Wet Test Meter.NOTE1The meter is used to measure the volume of dry ga
8、s in litersand hence the weight of SF6samples.The density of sulfur hexafluorideat 0C and 1 atm.of pressure(STP)is 6.52 g/L.The density of sulfurhexafluoride at 25C and 1 atm.of pressure(normal temperature andpressure)is 5.97 g/L.Alternatively,the sample weight may be determinedby weighing the sampl
9、e cylinder before and after sampling.6.Reagents6.1 Purity of ReagentsUse reagent grade chemicals in alltests.Unless otherwise indicated,it is intended that all reagentsshall conform to the specifications of the Committee onAnalytical Reagents of the American Chemical Society,wheresuch specifications
10、 are available.3Other grades may be used,provided it is first ascertained that the reagent is of sufficientlyhigh purity to permit its use without lessening the accuracy ofthe determination.6.2 Purity of WaterUnless otherwise indicated,referencesto water shall be understood to mean reagent grade wat
11、erconforming to Specification D1193.6.3 Phenolphthalein Indicator Solution(10 g/L)Dissolve1 g of phenolphthalein in 100 mL of ethanol(95%).6.4 Sodium Hydroxide Solution(0.01 N)Dissolve 0.4 60.01 g of sodium hydroxide(NaOH)in water and dilute to 1 L.Prepare a fresh solution weekly.Standardize by titr
12、atingagainst a weighed amount of potassium acid phthalate.6.5 Sulfuric Acid(0.01 N)Add 0.25 mL of concentratedsulfuric acid(H2SO4,sp gr 1.84)to water and dilute to 1 L.Standardize against standard 0.01 N NaOH solution.7.Sampling7.1 Take the sample as a liquid from the cylinder to besampled.This may
13、be done by inverting the cylinder so that theoutlet valve is at the bottom.1This test method is under the jurisdiction of ASTM Committee D27 onElectrical Insulating Liquids and Gases and is the direct responsibility of Subcom-mittee D27.06 on Chemical Test.Current edition approved Dec.1,2019.Publish
14、ed December 2019.Originallyapproved in 1964 as D2284 64T.Last previous edition approved in 2011 asD2284 11.DOI:10.1520/D2284-11R19.2The boldface numbers in parentheses refer to a list of references at the end ofthis standard.3Reagent Chemicals,American Chemical Society Specifications,AmericanChemica
15、l Society,Washington,DC.For Suggestions on the testing of reagents notlisted by the American Chemical Society,see Analar Standards for LaboratoryChemicals,BDH Ltd.,Poole,Dorset,U.K.,and the United States Pharmacopeiaand National Formulary,U.S.Pharmacopeial Convention,Inc.(USPC),Rockville,MD.Copyrigh
16、t ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.18.Preparation of Apparatus8.1 Place the cylinder to be sampled as suggested in Sectio
