1、Designation:D257219Standard Test Method forIsocyanate Groups in Urethane Materials or Prepolymers1This standard is issued under the fixed designation D2572;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A n
2、umber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method covers the determination of the isocya
3、-nate group(NCO)content of a urethane intermediate orprepolymer.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is ther
4、esponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For specific hazard statements,see Section 8.1.4 This international standard was developed in accor-dance with intern
5、ationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D841 Speci
6、fication for Nitration Grade Toluene3.Summary of Test Method3.1 The urethane prepolymer is allowed to react with anexcess of di-n-butylamine in toluene(Note 1).After thereaction is complete,the excess of di-n-butylamine is deter-mined by back titration with standard hydrochloric acid.NOTE1Solvents o
7、ther than toluene may be needed in some cases,forexample,anhydrous dimethylformamide(DMF),but the procedure hasnot been evaluated using them.4.Significance and Use4.1 The percent NCO is used to establish unit ratios forstoichiometric reactions with co-reactants.5.Interferences5.1 Phosgene,the carbam
8、yl chloride of isocyanate,hydro-gen chloride,or any other acidic or basic impurities ofsufficient strength will interfere.The concentration of thesecompounds is usually sufficiently low that their effect on thedetermination is negligible.6.Apparatus6.1 Polyethylene Stoppers(or corks)covered with alu
9、mi-num foil to fit 250-mL Erlenmeyer flasks.6.2 Magnetic Stirrer with PTFE-fluorocarbon-covered stir-ring bar.6.3 Pipet,325-mL.6.4 Buret,350-or 100-mL.6.5 Analytical Balance.7.Reagents7.1 Purity of ReagentsReagent grade chemicals shall beused in all tests unless otherwise specified.Unless otherwisei
10、ndicated,it is intended that all reagents shall conform to thespecifications of the Committee on Analytical Reagents of theAmerican Chemical Society,where such specifications areavailable.4Other grades may be used,provided that it is firstascertained that the reagent is of sufficiently high purity t
11、opermit its use without lessening the accuracy of the determi-nation.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.33 on Polymers and Resins.Current edition approved Oct.1,
12、2019.Published October 2019.Originallyapproved in 1967.Last previous edition approved in 2010 as D2572 97(2010)which was withdrawn in July 2019 and reinstated October 2019.DOI:10.1520/D2572-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at servi
13、ceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Burets and pipets shall conform to National Institute of Standards andTechnology tolerances.4ACS Reagent Chemicals,Specifications and Procedures for Reagents andStandard-Gr
14、ade Reference Materials,American Chemical Society,Washington,DC.For suggestions on the testing of reagents not listed by the American ChemicalSociety,see Analar Standards for Laboratory Chemicals,BDH Ltd.,Poole,Dorset,U.K.,and the United States Pharmacopeia and National Formulary,U.S.Pharma-copeial
15、Convention,Inc.(USPC),Rockville,MD.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principl
16、es for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 7.2 Bromphenol Blue Indicator,Prepare 0.1%solution bymixing 0.10 g of acid,nonwater soluble bromphenol blue with1.5 mL of 0.1 N sodium hydroxide solution and diluting to 100mL with distilled water.7.3 Di-n-butylamine Solution,0.1 N in dry toluene.Notstandardized.7.4 Hydrochloric Acid Solution,0.1 N standardized usingbromphenol blue indicat
