收藏 分享(赏)

ASTM_D_3883_-_04_2020.pdf

上传人:益****师 文档编号:183018 上传时间:2023-03-04 格式:PDF 页数:4 大小:83.44KB
下载 相关 举报
ASTM_D_3883_-_04_2020.pdf_第1页
第1页 / 共4页
ASTM_D_3883_-_04_2020.pdf_第2页
第2页 / 共4页
ASTM_D_3883_-_04_2020.pdf_第3页
第3页 / 共4页
ASTM_D_3883_-_04_2020.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D388304(Reapproved 2020)Standard Test Method forYarn Crimp and Yarn Take-up in Woven Fabrics1This standard is issued under the fixed designation D3883;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revis

2、ion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the rela-tionship between the length of a piece of fabric and the lengthof the yarn in t

3、he fabric by measurement of the yarn crimp andyarn take-up.1.2 This test method applies to woven fabrics.1.3 The values stated in either SI or inch-pound units are tobe regarded separately as standard.Within the text,theinch-pound units are shown in parentheses.The values statedin each system are no

4、t exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in nonconformancewith the specification.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of

5、the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization establishe

6、d in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1776/D1776M Practice for Condition

7、ing and Testing Tex-tilesD2904 Practice for Interlaboratory Testing of a Textile TestMethod that Produces Normally Distributed Data(With-drawn 2008)3D2906 Practice for Statements on Precision and Bias forTextiles(Withdrawn 2008)3D4849 Terminology Related to Yarns and FibersD4850 Terminology Relating

8、 to Fabrics and Fabric TestMethods3.Terminology3.1 For definition of textile terms used in this test method:bench marks,refer to Terminology D4849.3.2 For definitions of textile terms used in this test method:yarn crimp and yarn take-up,refer to Terminology D4850.3.3 For definitions of other textile

9、 terms used in this testmethod,refer to Terminology D123.4.Summary of Test Method4.1 Bench marks are placed on a length of a yarn as it liesin a woven fabric.The distance between the bench marks ismeasured.The yarn is removed from the fabric,straightened byapplying suitable tension,and the distance

10、between the benchmarks is remeasured.Yarn crimp is the change in lengthexpressed as a percent and based on the in-fabric distance.Yarntake-up is the change in length expressed as a percent andbased on the out-of-fabric distance.5.Significance and Use5.1 The relationship of the length of a piece of f

11、abric and thelength of yarn in the fabric can be determined accurately onlybe measuring the length of yarn entering the loom and thelength of fabric made from that particular length of yarn.Inmost cases,however,the determination must of necessity bemade on a woven fabric by measuring the length of y

12、arnremoved from a measured length of fabric,thus introducingcertain variations that will influence the accuracy of the test.Yarn removed from the woven fabric contains undulations orwaves that have been introduced by the weaving process.Heat,moisture,and mechanical shrinkage on subsequent finishingo

13、perations may accentuate these undulations,and in all1This test method is under the jurisdiction ofASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.59 on Fabric Test Methods,General.Current edition approved July 1,2020.Published August 2020.Originallyapproved in 198

14、0.Last previous edition approved in 2016 as D3883 04(2016).DOI:10.1520/D3883-04R20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page on

15、the ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized pri

16、nciples on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1probability,increase the force to pull them out and straightenthe yarn.In order to accurately measure the length of the yarnafter the removal of the crimp,these undulations must bepulled out without elongating the yarn.In some cases,theminimum force necessary to straighten th

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2