1、Designation:D 255 92Standard Method forSteam Distillation of Bituminous Protective Coatings1This standard is issued under the fixed designation D 255;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number
2、in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This is a general method for the separation by steamdistillation
3、 and the recovery of solvent and base from bitumi-nous mixtures.1.2 The following safety hazards caveat pertains only to thetest methods described in this specification.This standard doesnot purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the
4、user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2.Referenced Documents2.1 ASTM Standards:D 140 Practice for Sampling Bituminous Materials2E 1 Specification for ASTM Thermometers33.Apparatus3.1 Steam Genera
5、tor,made of either metal or glass,with acapacity of approximately 2 gal(7600 cm3),suitable forcontinued use in the production of steam.If of glass,it shall befitted with two outlets having suitable connections for rubbertubing.In the case of a metal generator,a large opening forfilling and a water g
6、age shall be additional parts of theapparatus.The generator shall be supplied with suitable pinch-cocks or valves so that steam may be blown off to theatmosphere until the test is ready.NOTE1The following conversion factors are given for volumetricglassware graduated in litres:1 L 5 1 dm3or 1000 cm3
7、(1)1 mL 5 1 cm33.2 Bath,made of metal and having sufficient capacity topermit immersion of the distilling flask to a depth of not lessthan 4 in.(101.6 mm).3.3 Source of Heatfor the bath,such as a gas burner,electric hot plate,or the equivalent.An electric mantle typeheater,equipped with a variable r
8、esistance transformer ofsuitable size and heat capacity,is a suitable replacement for thebath and heat source.3.4 Distilling Flask,1000-cm3,heat-resistant glass,with ashort ring neck and round bottom.It shall be fitted with athree-hole rubber stopper,a steam delivery tube that will reachto within386
9、18in.(9.5 6 4.7 mm)of the bottom of the flaskand project from the top to a convenient distance forconnection to the generator,a vapor outlet tube extending frombeneath the rubber stopper to a point sufficiently above thedistilling flask to permit convenient connection to thecondenser,and a thermomet
10、er.The steam tubing shall be notless than 2 nor more than 4 mm in internal diameter,and thevapor outlet tube shall be not less than 5 mm in internaldiameter.3.5 Thermometer,ASTM Low Distillation,having a rangeof 2 to+300C(30 to 580F),as specified,and conformingto the requirements for thermometer 7C
11、or 7F,respectively,asprescribed in Specification E 1.3.6 CondenserA glass-jacketed condenser.The followingdimensions are recommended:Length of jacket,excluding the necks250 6 5 mmLength of condenser tube400 6 25 mmOutside diameter of condenser tube proper12.5 6 0.5 mmOutside diameter of expanded end
12、 of tube23 6 1 mmLength of expanded end of tube75 6 1 mm3.7 AdapterA heavy-wall(1 mm)glass adapter,withreinforced top,having an angle of approximately 105.Theinside diameter at the large end shall be approximately 18 mmand at the small end,not less than 5 mm.The lower surface ofthe adapter shall be
13、on a smooth descending curve from thelarger end to the smaller.The inside line of the outlet end shallbe vertical and the outlet shall be cut or ground(not fire-polished)at an angle of 45 6 5 to the inside line.3.8 ReceiverGraduated cylinders of uniform diameter,with a pressed or molded base and a l
14、ipped top.The over-allheight shall be 10 6 0.250 in.(254 6 6.35 mm).The cylindershall be graduated in single millilitres to contain 100 cm3,andthe graduated portion shall be 7.5 6 0.500 in.(190.5 6 12.70mm)in length.3.9 Separatory FunnelA separatory funnel having acapacity of not less than 500 cm3.1
15、This method is under the jurisdiction of ASTM Committee D-8 on Roofing,Waterproofing,and Bituminous Materials and is the direct responsibility ofSubcommittee D08.05 on Solvent-Bearing Bituminous Compounds for Roofing andWaterproofing.Current edition approved April 15,1992.Published June 1992.Origina
16、llypublished as E 255 26.Last previous edition D 255 70(82)e1.2Annual Book of ASTM Standards,Vol 04.03.3Annual Book of ASTM Standards,Vol 14.01.1AMERICAN SOCIETY FOR TESTING AND MATERIALS100 Barr Harbor Dr.,West Conshohocken,PA 19428Reprinted from the Annual Book of ASTM Standards.Copyright ASTM4.Sampling4.1 Take the samples for laboratory examination from theoriginal containers immediately after stirring to a uniformcondition.Determine the number of containers sampled torepresent a shipment in
