1、Designation:D126511(Reapproved 2017)1Standard Practice forSampling Liquefied Petroleum(LP)Gases,Manual Method1This standard is issued under the fixed designation D1265;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTESI units formatting was corrected editorially in July 2017.1.Scope1.1 This practice covers equipment and procedures forobtaining a rep
3、resentative sample of specification LiquefiedPetroleum Gas(LPG),such as specified in SpecificationD1835,GPA 2140,and comparable international standards.1.2 This practice is suitable for obtaining representativesamples for all routine tests for LP gases required by Specifi-cation D1835.In the event o
4、f a dispute involving sampleintegrity when sampling for testing against SpecificationD1835 requirements,Practice D3700 shall be used as thereferee sampling procedure.1.3 This practice may also be used for other Natural GasLiquid(NGL)products that are normally single phase(NGLmix,field butane,etc.),d
5、efined in other industry specificationsor contractual agreements.It is not intended for non-specification products that contain significant quantities ofundissolved gases(N2,CO2),free water or other separatedphases,such as raw or unprocessed gas/liquids mixtures andrelated materials.The same equipme
6、nt can be used for thesepurposes,but additional precautions are generally needed toobtain representative samples of multiphase products(seeAppendix X1 on Sampling Guidelines in Practice D3700).NOTE1Practice D3700 describes a recommended practice for obtain-ing a representative sample of a light hydr
7、ocarbon fluid and the subse-quent preparation of that sample for laboratory analysis when dissolvedgases are present.Use of Practice D1265 will result in a small butpredictable low bias for dissolved gases due to the liquid ventingprocedure to establish the 20%minimum ullage.1.4 This practice includ
8、es recommendations for the locationof a sample point in a line or vessel.It is the responsibility ofthe user to ensure that the sampling point is located so as toobtain a representative sample.1.5 The values stated in SI units are to be regarded asstandard.1.5.1 ExceptionNon-SI units are shown in pa
9、rentheses forinformation only.1.6This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations pr
10、ior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalB
11、arriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1835 Specification for Liquefied Petroleum(LP)GasesD3700 Practice for Obtaining LPG Samples Using a Float-ing Piston Cylinder2.2 Other Regulations:Canadian Transportation of Dangerous Goods Regulations3GPA 2140 Gas Processors
12、Association Liquefied PetroleumGas Specifications&Test Methods4IATA Transportation of Dangerous Goods by Air5U.S.CFR 49 Transportation63.Terminology3.1 Definitions:3.1.1 high pressure sample cylinder,na container used forstorage and transportation of a sample obtained at pressuresabove atmospheric p
13、ressure.1This practice is under the jurisdiction of ASTM Committee D02 on PetroleumProducts,Liquid Fuels,and Lubricants and is the direct responsibility of Subcom-mittee D02.H0 on Liquefied Petroleum Gas.Current edition approved May 1,2017.Published July 2017.Originally approvedin 1953.Last previous
14、 edition approved in 2011 as D1265 11.DOI:10.1520/D1265-11R17E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3
15、Available from the Canadian General Standards Board,Sales Centre,Gatineau,Canada K1A 1G6,http:/www.ongc-cgsb.gc.ca/.4Available from Gas Processors Association(GPA),6526 E.60th St.,Tulsa,OK74145,http:/www.gpaglobal.org.5Available from IATA Customer Care,800 Place Victoria,PO Box 113,Montral,Quebec H4
16、Z 1M1.www.iata.org.6Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and R
