收藏 分享(赏)

ASTM_D_1710_-_15_2021.pdf

上传人:益****师 文档编号:184060 上传时间:2023-03-04 格式:PDF 页数:5 大小:138.22KB
下载 相关 举报
ASTM_D_1710_-_15_2021.pdf_第1页
第1页 / 共5页
ASTM_D_1710_-_15_2021.pdf_第2页
第2页 / 共5页
ASTM_D_1710_-_15_2021.pdf_第3页
第3页 / 共5页
ASTM_D_1710_-_15_2021.pdf_第4页
第4页 / 共5页
ASTM_D_1710_-_15_2021.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D171015(Reapproved 2021)Standard Specification forExtruded Polytetrafluoroethylene(PTFE)Rod,Heavy WalledTubing and Basic Shapes1This standard is issued under the fixed designation D1710;the number immediately following the designation indicates the year oforiginal adoption or,in the case

2、 of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specific

3、ation covers extruded polytetrafluoroethyl-ene(PTFE)rod,heavy-walled tubing,and basic shapes manu-factured from the PTFE resin of Specification D4894 andreprocessed PTFE resin(as defined in Guide D7209).1.2 The specification covers all sizes of rod,tubing,andbasic shapes with a wall thickness of 1.6

4、 mm(116in.)orgreater.These materials must be made wholly from PTFE andproduced in accordance with good commercial ram extrusionpractices.NOTE1This specification and ISO/DIS 13000-1(1997)and ISO/DIS13000-2(1997)differ in approach,however,data obtained using either aretechnically equivalent.NOTE2For c

5、ompression molded PTFE materials,see SpecificationD3294.Material that can be certified to Specification D3294 may besubstituted for Specification D1710,however the reverse in not true.1.3 The values stated in SI units,as detailed in IEEE/ASTMSI 10 are to be regarded as the standard.The inch-pound un

6、itsgiven in parentheses are provided for information only.1.4 The following precautionary caveat pertains to the testmethods portion,Section 12,only of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of th

7、e userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in th

8、e Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D149 Test Method for Dielectric Breakdown Voltage andDielectric Strength of Sol

9、id Electrical Insulating Materialsat Commercial Power FrequenciesD374 Test Methods for Thickness of Solid Electrical Insu-lation(Metric)D0374_D0374MD618 Practice for Conditioning Plastics for TestingD792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD883

10、Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD3892 Practice for Packaging/Packing of PlasticsD4894 Specification for Polytetrafluoroethylene(PTFE)Granular Molding and Ram Extrusion MaterialsD5740 Guide for Writing Material Standards in the Classi-ficati

11、on FormatD5947 Test Methods for Physical Dimensions of SolidPlastics SpecimensD7209 Guide for Waste Reduction,Resource Recovery,andUse of Recycled Polymeric Materials and Products(With-drawn 2015)3E94 Guide for Radiographic Examination Using IndustrialRadiographic FilmIEEE/ASTM SI 10 Standard for th

12、e Use of the InternationalSystem of Units(SI):The Modern Metric System42.2 ISO Standards:5ISO 13000-1(2005)PlasticsPolytetrafluoroethylene(PTFE)Semi-Finished Products,Part 1:Basis for Speci-fication1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct respo

13、nsibility of Subcommittee D20.15 on ThermoplasticMaterials.Current edition approved Oct.1,2021.Published October 2021.Originallyapproved in 1960.Last previous edition approved in 2015 as D1710-15.DOI:10.1520/D1710-15R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact AST

14、M Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from ASTM International,100 Barr Harbor Drive,WestC

15、onshohocken,PA 19428.5Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accor

16、dance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1ISO 13000-2(2005)PlasticsPolytetrafluoroethylene(PTFE)Semi-Finished Products,Part 2:Preparation ofTest Specimen and Determination of Properties3.Terminology3.1 Definitions:3.1.1 Definitions are in accordance with Terminology D883unless

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2