收藏 分享(赏)

ASTM_D_1061_-_D_1061M_-_95_2009e1.pdf

上传人:益****师 文档编号:184187 上传时间:2023-03-04 格式:PDF 页数:4 大小:80.47KB
下载 相关 举报
ASTM_D_1061_-_D_1061M_-_95_2009e1.pdf_第1页
第1页 / 共4页
ASTM_D_1061_-_D_1061M_-_95_2009e1.pdf_第2页
第2页 / 共4页
ASTM_D_1061_-_D_1061M_-_95_2009e1.pdf_第3页
第3页 / 共4页
ASTM_D_1061_-_D_1061M_-_95_2009e1.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D1061/D1061M95(Reapproved 2009)1Standard Specification forAsbestos Lap1This standard is issued under the fixed designation D1061/D1061M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in

2、 parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEUnits information was corrected editorially in March 2010.1.Scope1.1 This specification covers asbestos lap,a felted asbestosproduct,having a minimum of 7

3、5 mass%of asbestos fiber.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in

4、 non-conformancewith the standard.1.3 WarningBreathing of asbestos dust is hazardous.Asbestos and asbestos products present demonstrated healthrisks for users and for those with whom they come into contact.In addition to other precautions,when working with asbestos-cement products,minimize the dust

5、that results.For informa-tion on the safe use of chrysoltile asbestos,refer to“Safe Useof Chrysotile Asbestos:A Manual on Preventive and ControlMeasures.”21.4 The following safety hazards caveat pertains only to thetest methods,Section 12,described in this specification:Thisstandard does not purport

6、 to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.For specific safety hazard,see 1.3.2.Referenced Docum

7、ents2.1 ASTM Standards:3D123 Terminology Relating to TextilesD1118 Test Method for Magnetic Rating of Asbestos Fiberand Asbestos TextilesD1918 Test Method for Asbestos Content of Asbestos Tex-tilesD2946 Terminology for Asbestos and AsbestosCementProducts3.Terminology3.1 For definitions of other text

8、ile terms used in thisspecification refer to Terminology D123.For asbestos termsrefer to Terminology D2946.3.2 Definitions:3.2.1 asbestosa group of impure silicate minerals occur-ring in fibrous form.3.2.2 asbestos fiberthe hydrous magnesium silicate ser-pentine mineral designated as chrysotile and

9、having the em-pirical formula Mg3Si2O5(OH)4.3.2.3 atmosphere for testing textiles for asbestos,airmaintained at a relative humidity of 50 6 2%at 21 6 1C.3.2.4 lap,nfor asbestos,a flat compressed form of cardedor otherwise felted asbestos fiber,with or without carrier fibers.3.2.5 magnetic rating(MR)

10、an empirical value that reflectsthe effect of magnetic particles,such as magnetic ironcompounds,in asbestos material as measured by a magneticanalyzer.NOTE1Magnetic rating is not a quantitative measure of the number ormass of magnetic particles in the material.4.Classifications4.1 StylesThe style of

11、 asbestos lap refers to the physicalconstruction.Two styles are available:4.1.1 Style 1A single compressed flat formation of cardedor otherwise felted asbestos fibers,and4.1.2 Style 2A flat parallel assemblage of compressedcarded asbestos slivers.4.2 GradesThe grades of asbestos lap are based on the

12、mass percentage of asbestos content as stated in Table 1.4.3 Mass per Unit LengthAsbestos lap is normally fur-nished in the following nominal linear densities:1This specification is under the jurisdiction of ASTM Committee C17 onFiber-Reinforced Cement Productsand is the direct responsibility of Sub

13、committeeC17.03 on Asbestos-Cement Sheet Products and Accessories.Current edition approved Nov.1,2009.Published March 2010.Originallyapproved in 1949.Last previous edition approved in 2004 as D1061 95(2004)1.DOI:10.1520/D1061_D1061M-95R09E01.2Available from The Asbestos Institute,http:/ referenced A

14、STM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA

15、 19428-2959.United States1 g/mlb/100 yd204501070141002015030Other linear densities may be furnished as agreed uponbetween the purchaser and the seller.4.4 Types:4.4.1 Asbestos lap as made for the electrical industry isfurnished in three types,classified on the basis of magneticrating determinations(

16、Test Method D1118)as follows:4.4.2 Type II(Magnetic Rating 0.75 Maximum)is intendedonly for special applications where the asbestos is of primaryimportance as electrical insulation used on magnet wire andwhen used primarily as a dielectric.4.4.3 Type IV(Magnetic Rating 2.00 Maximum)is intendedfor use where the asbestos is of secondary importance aselectrical insulation and where it is applied in combination withother materials of comparably higher dielectric strength,as inthe construction of hea

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2