1、Designation:B967/B967M16Standard Specification forCopper-Zinc-Tin-Bismuth Alloy Rod,Bar and Wire1This standard is issued under the fixed designation B967/B967M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision
2、.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification establishes the requirements forcopper-zinc-tin-bismuth alloy rod,bar and wire of alloy UNSNos.C49250,C49255,C49260
3、,C49265,C49300,C49340,C49345,C49350,C49355,and C49360 intended for use inplumbing applications and drinking water systems.1.2 Typically,rod and bar product made to this specificationis furnished as straight lengths.Wire(H04)0.08 to 0.3 in.2 to8 mm inclusive is furnished in coil form,and H50 shapes.1
4、.3 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in non-conformance w
5、ith the standard.1.4 The following safety hazard caveat pertains only to thetest method(s)described in this specification.1.4.1 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-p
6、riate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2B249/B249M Specification for General Requirements forWrought Copper and Copper-Alloy Rod,Bar,Shapes andForgingsB250/B250M Specification for General Requ
7、irements forWrought Copper Alloy WireB846 Terminology for Copper and Copper AlloysE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE54 Test Methods for Chemical Analysis of Special Brassesand Bronzes(Withdrawn 2002)3E62 Test Methods for Chemical Analysis of Copper andCopperAlloys(Photom
8、etric Methods)(Withdrawn 2010)3E92 Test Methods for Vickers Hardness and Knoop Hard-ness of Metallic MaterialsE478 Test Methods for Chemical Analysis of Copper AlloysE527 Practice for Numbering Metals and Alloys in theUnified Numbering System(UNS)2.2 Other Standards:ISO No.3110(AA)Copper Alloys Dete
9、rmination of Alu-minum as an Alloying Element Volumetric4(Interna-tional Organization of Standardization)JIS H 1068:2005 Method for Determination of Bismuth inCopper and Copper Alloys5(Japanese Industrial Stan-dards)3.General Requirements3.1 The following sections of Specifications B249/B249Mfor rod
10、 and bar and B250/B250M for wire constitute a part ofthis specification:3.1.1 Terminology,3.1.2 Materials and Manufacture,3.1.3 Sampling,3.1.4 Number of Tests and Retests,3.1.5 Specimen Preparation,3.1.6 Certification,3.1.7 Test Reports.3.2 In addition,when a section with a title identical to thatre
11、ferencedin AppendixX1,above,appearsinthisspecification,it contains additional requirements which supple-ment those appearing in Specifications B249/B249M for rodand bar and B250/B250M for wire.4.Terminology4.1 For definitions of terms related to copper and copperalloys,refer to Terminology B846.1Thi
12、s specification is under the jurisdiction ofASTM Committee B05 on Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,Bar,Wire,Shapes and Forgings.Current edition approved Oct.1,2016.Published November 2016.Originallyapproved in 2009.Last previous edition approved
13、in 2012 as B967/B967M 12a.DOI:10.1520/B0967_B0967M-16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last ap
14、proved version of this historical standard is referenced onwww.astm.org.4Available from International Organization for Standardization(ISO),ISOCentral Secretariat,BIBC II,Chemin de Blandonnet 8,CP 401,1214 Vernier,Geneva,Switzerland,http:/www.iso.org.5Available from Japanese StandardsAssociation(JSA
15、),Mita MT Bldg.,3-13-12Mita,Minato-ku,Tokyo 108-0073,Japan,http:/www.jsa.or.jp.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.Ordering Information5.1 Include the followin
16、g information when placing ordersfor product under this specification,as applicable:5.1.1 ASTM designation and year of issue;5.1.2 Copper Alloy UNS designation;5.1.3 Temper(Section 8);5.1.4 Dimensions,diameter,or distance between parallelsurfaces;5.1.5 How furnished:straight lengths or coils;5.1.6 Quantity:total weight or total length or number ofpieces of each size;5.1.7 If product is purchased for agencies of the U.S.Government(see the Supplementary Requirements section ofSpecifications B249/B
