1、Designation:C115406(Reapproved 2016)Standard Terminology forNon-Asbestos Fiber-Reinforced Cement Products1This standard is issued under the fixed designation C1154;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi
2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This standard covers definitions pertaining to non-asbestos fiber-reinforced cement products under the jurisdic-tion of Committee C1
3、7.2.Referenced Documents2.1 ASTM Standards:2C150 Specification for Portland CementC618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozzolan for Use in ConcreteC966 Guide for Installing Asbestos-Cement NonpressurePipeC1185 Test Methods for Sampling and Testing Non-Asbestos Fiber-Cement
4、Flat Sheet,Roofing and SidingShingles,and ClapboardsC1186 Specification for Flat Fiber-Cement SheetsC1449 Specification for Non-Asbestos Fiber-Cement Non-pressure Sewer PipeD1118 Test Method for Magnetic Rating of Asbestos Fiberand Asbestos Textiles3.Terminologyaccessories,nsubordinate material such
5、 as fasteners,backerstrips,closure strips,ridge and corner rolls,roofing startersand finishing pieces,couplings,gaskets,pipe fittings or othersupplementary material necessary for the proper applicationof primary fiber-reinforced cement products.American method,nin shingles,a method of application fo
6、rroofing shingles,generally rectangular in shape,to providedouble coverage with head lap and no side lap.AOQL,nThe average outgoing quality limit of a samplingplan is the maximum value of the proportion defectiveaccepted on average by that plan.AOQL is the maximumvalue of the multiplicand of the pro
7、portion nonconformingand the probability of acceptance from the sampling planoperating characteristic.asphalt felt,breather type,nan underlayment sheet mate-rial saturated with asphalt,which allows the transmission ofwater vapor.autoclaved products,nthose that have been treated in asaturated steam a
8、tmosphere at between 620 and 1517 kPa(90 and 220 psi,)for at least 6 h,and that contain portlandcement as defined in Specifications C150 and C618 togetherwith silica in the ratio of 3:2 that can react to form calciumsilicate reaction products.backer strips,nin shingles,water-repellent strips of asph
9、alt-coated felt applied behind each joint where the vertical edgesof two shingles meet.batten,na long narrow strip,either flat or corrugated,used toconceal the joints in butt joint application of flat or corru-gated sheets.caulking,na material ranging in physical characteristicsfrom plastic,to solid
10、,to preformed,used to seal andwaterproof joints and overlaps in structures,otherassemblies,or portions thereof where movement may occur.cement-bonded particle board,nmanufactured flat sheetsof hydraulic cementitious matrices and fibrous wood par-ticles.clip,nin shinglesSee storm anchor.closure strip
11、,nan asphalt or rubber preformed filler striphaving the same shape and pitch as the corrugated product,used to close openings in the corrugated sheets at windowbeads,eaves,lower edge of siding,and similar pacted backfill,nin pipe laying,backfill material whichhas been compacted to the density specif
12、ied by the engineer.conduit,npipe used to protect wires for electric-power orcommunication systems,for both underground and exposedsituations.constructor,nin pipe laying,the party that furnishes thework and materials for placement and installation.1This terminology is under the jurisdiction of ASTM
13、Committee C17 onFiber-Reinforced Cement Products and is the direct responsibility of SubcommitteeC17.02 on Non-Asbestos Fiber Cement Products.Current edition approved Nov.1,2016.Published November 2016.Originallyapproved in 1990.Last previous edition approved in 2011 as C115406(2011).DOI:10.1520/C11
14、54-06R16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box
15、 C700,West Conshohocken,PA 19428-2959.United States1 corner rolls,nhalf-round units used to trim and flash cornersin corrugated application.corrugated,adjpertaining to a sheet product having a designof sinusoidal alternating ridges and valleys manufacturedaccording to a specific pitch.coupling,nin f
16、iber-cement nonpressure sewer pipe,a sectionfor joining nonpressure sewer pipe,that when properlyinstalled with the proper accessories,develops an assembledjoint equivalent in serviceability and strength to the pipesections,when tested in accordance with 6.3.1 of Specifica-tion C1449.coupling,nin fiber-cement conduit,underdrain and stormdrain pipe,component made from a larger diameter pipe ofthe same type or class,or of Type II and a higher class,orproduced otherwise to yield at least equal perf
