1、Designation:A88815Standard Specification forHubless Cast Iron Soil Pipe and Fittings for Sanitary andStorm Drain,Waste,and Vent Piping Applications1This standard is issued under the fixed designation A888;the number immediately following the designation indicates the year oforiginal adoption or,in t
2、he case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers hubless cast iron soil pipe andfittings for use in gravity flow a
3、pplications.It establishesstandards covering material,manufacture,mechanical andchemical properties,dimensions,coating,test methods,inspection,certification,and product marking for hubless castiron soil pipe and fittings.These pipe and fittings are intendedfor non-pressure applications,as the select
4、ion of the propersize for sanitary drain,waste,vent,and storm drain systemsallows free air space for gravity drainage.1.2 The EDP/ASA numbers indicated in this section repre-sent a Uniform Industry Code adopted by theAmerican SupplyAssociation(ASA).A group designation prefix,022,is as-signed to hubl
5、ess products,followed by the four-digit identi-fication assigned to individual items and a check digit.Thissystem has been instituted to facilitate EDP control throughdistribution channels,and is to be used universally in orderingand specifying product items.Those items with no EDPnumbers are either
6、 new,special,or transitory and will beassigned numbers on subsequent prints of this specification.1.3 This specification covers pipe and fittings of the follow-ing patterns and applies to any other patterns that conform withthe applicable requirements given in this specification.21.3.1 Lengths:Figur
7、esEDP/ASA Identification Numbersfor Hubless PipeFig.110 ft(3.0 m)in sizes and 5 ft.(1.5 m)112,2,3,4,5,6,8,10,12,and 15 in.Fig.1,Fig.2Method of Specifying FittingsFig.31.3.2 Fittings:Quarter BendFig.5Quarter Bend,ReducingFig.6Quarter Bend,With Side OpeningFig.7Quarter Bend,With Heel OpeningFig.8Quart
8、er Bend,TappedFig.9Quarter Bend,DoubleFig.10Quarter Bend,LongFig.11Short SweepFig.12Long SweepFig.13Long Sweep,ReducingFig.14Fifth BendFig.15Sixth BendFig.16Eighth BendFig.17Eighth Bend LongFig.18Sixteenth BendFig.19Sanitary TeeFig.20Sanitary Tee With Side OpeningFig.21Sanitary Tee With 2 in.Side Op
9、ening R or L/R and LFig.22Sanitary Tee,New Orleans Special With Side OpeningFig.23Sanitary Tee With 45 Side Openings and New OrleansFig.24Sanitary Special Tee TappedFig.25Sanitary Tapped Tee,Horizontal TwinFig.26Sanitary Tapped Tee,Double VerticalFig.27Y BranchFig.28Y Branch,DoubleFig.29Y Branch,Upr
10、ightFig.30Upright Y Wide Center Florida SpecialFig.31Y Branch,Combination18BendFig.32Y Branch,Combination18Bend DoubleFig.33Sanitary CrossFig.34Sanitary Cross With Side OpeningFig.35Sanitary Cross,New Orleans,With Side OpeningsFig.36Sanitary Cross,New Orleans,With 45 Special andRegular Side Openings
11、Fig.37Sanitary Cross,TappedFig.38Test TeeFig.39Tapped,Extension PieceFig.40Increaser-ReducerFig.41Increaser-Reducer,ShortFig.42Tapped AdapterFig.43Blind PlugFig.44Iron Body Cleanout-TappedFig.45P TrapFig.46P Trap,LongFig.47P Trap,Deep SealFig.48P Trap,With PrimerFig.49P Trap,With Tapped InletFig.50T
12、apped Inlet,DoubleFig.51Modified Combination Wye and18Bend,DoubleFig.52Modified Combination Wye and18Bend,Double,ExtendedFig.53Two-Way CleanoutFig.54Twin CleanoutFig.55Closet Bend,Regular and ReducingFig.56Closet Flange RiserFig.571This specification is under the jurisdiction of ASTM Committee A04 o
13、n IronCastings and is under the direct responsibility of Subcommittee A04.12 on Pipesand Tubes.Current edition approved Sept.15,2015.Published September 2015.Originallyapproved in 1990.Last previous edition approved in 2013 as A888 13a.DOI:10.1520/A0888-15.2Reprinted with permission from Cast Iron S
14、oil Pipe Institute(CISPI),2401Fieldcrest Dr.,Mundelein,IL60060,http:/www.cispi.org.Available fromAmericanNational Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.Unite
15、d States1 Tapping BossesFig.58Double Sweep Sanitary Tee(Extended)Fig.59Running Trap with Double VentsFig.60P Trap with Tapped or Hubless Side InletFig.61Vented Tub Wye Extended,DoubleFig.62Vented Tub Wye Extended Offset,Left or RightFig.63Vented Tub WyeFig.64Double Two Way CleanoutFig.651.4 The valu
16、es stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The committee with jurisdiction over this standard isaware of another comparable standard published by the CastIron Soil Pipe Institute,CISPI 301.NOTE1The text of this standard references notes and footnotes thatprovide explanatory material.These notes and footnotes(excluding thosein tables an
