1、Designation:C107116Standard Specification forFibrous Glass Duct Lining Insulation(Thermal and SoundAbsorbing Material)1This standard is issued under the fixed designation C1071;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year
2、 of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers fibrous
3、glass insulation used asa thermal and sound absorbing liner for interior surfaces ofducts,plenums,and other air handling equipment that handleair up to 250F(121C).1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI
4、 units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine
5、 the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2C167 Test Methods for Thickness and Density of Blanket orBatt Thermal InsulationsC168 Terminology Relating to Thermal InsulationC177 Test Method for Steady-State Heat Flux Measure-ments and Thermal T
6、ransmission Properties by Means ofthe Guarded-Hot-Plate ApparatusC390 Practice for Sampling and Acceptance of ThermalInsulation LotsC411 Test Method for Hot-Surface Performance of High-Temperature Thermal InsulationC423 Test Method for SoundAbsorption and SoundAbsorp-tion Coefficients by the Reverbe
7、ration Room MethodC518 Test Method for Steady-State Thermal TransmissionProperties by Means of the Heat Flow Meter ApparatusC665 Specification for Mineral-Fiber Blanket Thermal Insu-lation for Light Frame Construction and ManufacturedHousingC1104/C1104M Test Method for Determining the WaterVapor Sor
8、ption of Unfaced Mineral Fiber InsulationC1114 Test Method for Steady-State Thermal TransmissionProperties by Means of the Thin-Heater ApparatusC1304 Test Method for Assessing the Odor Emission ofThermal Insulation MaterialsC1338 Test Method for Determining Fungi Resistance ofInsulation Materials an
9、d FacingsC1617 Practice for Quantitative Accelerated LaboratoryEvaluation of Extraction Solutions Containing IonsLeached from Thermal Insulation on Aqueous Corrosionof MetalsE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE795 Practices for Mounting Test Specimens During Soun
10、dAbsorption TestsE2231 Practice for Specimen Preparation and Mounting ofPipe and Duct Insulation Materials to Assess SurfaceBurning CharacteristicsG21 Practice for Determining Resistance of Synthetic Poly-meric Materials to FungiG22 Practice for Determining Resistance of Plastics toBacteria(Withdraw
11、n 2002)32.2 Other Standards:CAN/ULC-S102 Method of Test for Surface Burning Char-acteristics of Building Materials and Assemblies4NAIMA Fibrous Glass Duct Liner Standard5NFPA 259 Test Method for Potential Heat of BuildingMaterials61This specification is under the jurisdiction of ASTM Committee C16 o
12、nThermal Insulation and is the direct responsibility of Subcommittee C16.23 onBlanket and Loose Fill Insulation.Current edition approved Sept.1,2016.Published September 2016.Originallyapproved in 1986.Last previous edition approved in 2012 as C1071 12.DOI:10.1520/C1071-16.2For referenced ASTM standa
13、rds,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Availabl
14、e from Underwriters Laboratories(UL),2600 N.W.Lake Rd.,Camas,WA 98607-8542,http:/.5Available from North American Insulation Manufacturers Association(NAIMA),44 Canal Center Plaza,Suite 310,Alexandria,VA 22314,http:/www.naima.org.6Available from National Fire Protection Association(NFPA),1 Batterymar
15、chPark,Quincy,MA 02169-7471,http:/www.nfpa.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 SMACNA HVAC Duct Construction Standards7UL 181 Factory-Made Air Ducts and Air Connectors4UL 723 Test for Surface Burning Characteristics of Bui
16、ldingMaterials43.Terminology3.1 For definitions of terms used in this specification,seeTerminology C168.4.Classification4.1 The insulation covered by this specification shall be ofthe following types:4.1.1 Type IBlanket in roll form up to 200 ft(61 m)inlength,36 to 72 in.(914 to 1829 mm)in width,and thicknessesof12to 3 in.(13 to 76 mm),in12-in.(13-mm)increments.4.1.2 Type IIBoard in sheet form,up to 120 in.(3048 mm)in length,up to 48 in.(1219 mm)in width,and thicknesses of12to 3 in.(13 to 76 mm)
