1、Designation:B313Standard Specification forSoft or Annealed Copper Wire1This standard is issued under the fixed designation B3;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revision.Anumber in parentheses indicates
2、the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers drawn and annealed or softround bare copper wire for electric
3、al purposes(see ExplanatoryNote 1).1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.2.1 ExceptionFor density,resistivity and temperat
4、ure,the values stated in SI units are to be regarded as standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica
5、-bility of regulatory limitations prior to use.2.Referenced Documents2.1 The following documents of the issue in effect at thetime of reference form a part of this specification to the extentreferenced herein:2.2 ASTM Standards:2B49 Specification for Copper Rod Drawing Stock for Elec-trical Purposes
6、B193 Test Method for Resistivity of Electrical ConductorMaterialsB258 Specification for Nominal Diameters and Cross-SectionalAreas ofAWG Sizes of Solid Round Wires Usedas Electrical Conductors2.3 Other Standards:NBS Handbook 100 Copper Wire Tables33.Ordering Information3.1 Orders for material under
7、this specification shall includethe following information:3.1.1 Quantity of each size,3.1.2 Wire size:diameter in inches(see 5.3 and Table 1),3.1.3 Type of copper,if special(Section 4),3.1.4 Package size(see 10.1),3.1.5 Special package marking,if required,and3.1.6 Place of inspection(see 7.1).4.Mate
8、rials4.1 The material shall be copper of such quality and puritythat the finished product shall have the properties and charac-teristics prescribed in this specification.NOTE1Specification B49 defines copper suitable for use.4.2 Copper bars of special qualities,forms,or types,as maybe agreed upon be
9、tween the manufacturer and the purchaser,and which will conform to the requirements prescribed in thisspecification may also be used.5.General Requirements(see Section 8)5.1 Tensile Strength and ElongationThe wire shall con-form to the requirements for elongation prescribed in Table 1(see Explanator
10、y Note 2).No requirements for tensile strengthare specified.For wire whose nominal diameter is more than0.001 in.(0.025 mm)greater than a size listed in Table 1,butless than that of the next larger size,the requirements of thenext larger size shall apply.5.2 ResistivityThe electrical resistivity at
11、20C shall notexceed 875.20 lb/mile2(0.15328 g/m2)(see ExplanatoryNote 5).5.3 Dimensions and Permissible VariationsThe wire sizesshall be expressed as the diameter of the wire in decimalfractions of an inch to the nearest 0.0001 in.(or 0.001 mm)(seeExplanatory Note 3).For diameters under 0.0100 in.(0
12、.254mm),the wire shall not vary from the specified diameter bymore than plus and minus 0.0001 in.(0.0025 mm),and fordiameters of 0.0100 in.(0.254 mm)and over the wire shall notvary from the specified diameter by more than plus and minus1%,expressed to the nearest 0.0001 in.(or 0.001 mm).1This specif
13、ication is under the jurisdiction of ASTM Committee B01 onElectrical Conductorsand is the direct responsibility of Subcommittee B01.04 onConductors of Copper and Copper Alloys.Current edition approved Oct.1,2013.Published October 2013.Originallyapproved in 1912.Last previous edition approved in 2012
14、 as B3 12.DOI:10.1520/B0003-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from National Institute
15、of Standards and Technology(NIST),100Bureau Dr.,Stop 1070,Gaithersburg,MD 20899-1070,http:/www.nist.gov.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.4 JointsNecessary joints in the completed wire and inthe wire and rods prior to fina
16、l drawing shall be made inaccordance with the best commercial practice.5.5 FinishThe wire shall be free of all imperfections notconsistent with the best commercial practice.6.Test Methods6.1 Tensile Strength and ElongationNo test for tensilestrength shall be required.6.1.1 The elongation of wire with a nominal diametergreater than 0.0808 in.(2.052 mm)shall be determined as thepermanent increase in length due to the breaking of the wire intension(see Explanatory Note 4).The elongation shall bemea
