1、Designation:A86104(Reapproved 2013)Standard Specification forHigh-Silicon Iron Pipe and Fittings1This standard is issued under the fixed designation A861;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A num
2、ber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers high-silicon iron pipe and pipefittings intended for corrosion-resistant service for both above-and below-grade cons
3、truction.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 Pipe and pipe fittings shall be the no-hub(MJ)or thehub and plain end des
4、ign.1.4 Pipe and pipe fittings shall be of the sizes specified inTable 1 and Table 2 and Figs.1-71 or other sizes that shall bepermitted to conform to the requirements given herein.1.4.1 Pipe:1.4.1.1 No-hub(MJ)(Fig.1):Size(in.)Length(ft)11272737471.4.1.2 Hub/Plain End(Fig.35):Size(in.)Length(ft)2737
5、4767871051251551.4.2 Fitting(No-hub)(MJ):Figs.Quarter Bends2Sixth Bends3Return Bends4Double-Branch Quarter Bend5Eighth Bends6Sixteenth Bends7Long-Sweep Quarter Bends8Sanitary Y Branches9Double-Branch Sanitary Y10Sanitary Combination Y and18Bend11Double-Branch Sanitary Combination Y and18Bend12Sanita
6、ry T Branches13Double Branch Sanitary T14Sanitary Running Traps15Sanitary P Traps16Swivel Trap P-Style Short17Swivel Trap P-Style Long18Swivel Trap S-Style Long19Centrifugal Drum Trap P Swivel Type20Centrifugal Drum Trap S Swivel Type21Combination Cleanout and Test Tees22Coupling23Pipe Plugs24Cleano
7、ut Plugs25No-hub(MJ)Adapter26ReducersIncreasers27Sink Outlet28Sink Overflows29Threaded Adapters30Trap Cleanout Details31No-hub(MJ)Adapter32(MJ)(No-hub)to Lead Adapter33Floor Drains341.4.3 Fitting(Hub/Plain End):Figs.Hub Plain End Pipe35Straight Tees36Sanitary T Branches37Sanitary Y Branches38Double-
8、Branch Sanitary Tee39Double-Branch Sanitary Y40Double-Branch Sanitary Combination Y and18Bend(T-Y)41Short-Sweep Quarter Bends42Long-Sweep Quarter Bends43Sanitary Combination Y and18Bend(T-Y)44Quarter Bends451This specification is under the jurisdiction of ASTM Committee A04 on IronCastings and is th
9、e direct responsibility of Subcommittee A04.12 on Pipes andTubes.Current edition approved May 1,2013.Published July 2013.Originally approvedin 1986.Last previous edition approved in 2008 as A861 04(2008).DOI:10.1520/A0861-04R13.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Cons
10、hohocken,PA 19428-2959.United States1 Sixth Bends46Eighth Bends47Sixteenth Bends48Sanitary Increasers49Hub Strainers50Sanitary Reducers51Double Hubs52Pipe Plugs53Cleanout Plugs54AdapterPlain end to Split Flange55AdapterHub to-Split Flange56Combination Cleanout and Test Tees57Insertable Joints58Backw
11、ater Valves59Sanitary P Traps60Sanitary S Traps61Sanitary Running Traps62Floor Drains63,64,65Floor Drains66Floor Drains/InstallationFunnel Attachment67,68Overflow69Sink Outlet70Detailed Cross Section of Cleanout71Chemical CompositionTable 3Transverse Bend Test Minimum RequirementsTable S1.12.Referen
12、ced Documents2.1 ASTM Standards:2A518/A518M Specification for Corrosion-Resistant High-Silicon Iron CastingsE350 Test Methods for Chemical Analysis of Carbon Steel,Low-Alloy Steel,Silicon Electrical Steel,Ingot Iron,andWrought IronE351 Test Methods for ChemicalAnalysis of Cast IronAllTypes2.2 Other
13、Standards:Uniform Classification Rules3National Motor Freight Classification33.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 hublessa pipe or fitting without a hub,sometimescalled no-hub,joined by a coupling.3.1.2 MJan abbreviation for mechanical joint.3.1.3 no-huba pipe or fit
14、ting without a hub,sometimesdescribed as hubless joined by a coupling.4.Ordering Information4.1 Ordering for material under this specification shallinclude as a minimum the following information:4.1.1 ASTM designation,grade(see Table 3)and year ofissue.4.1.2 Description of the casting by figure numb
15、er(see Figs.1 through 71)or by manufacturers drawings or catalognumber,or both.4.1.3 Length,diameter,and type of pipe and size and shapeof fittings.4.1.4 Quantity.4.1.5 Certification requirements.4.1.6 Special packaging requirements(see Section 14).2For referenced ASTM standards,visit the ASTM websi
16、te,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Trucking Association,950 North Glebe Road,Suite210,Arlington,VA 22203-4181.TABLE 1 Tolerances for High-Silicon Iron Hub/Plain-End PipeNOTE11 in.=25.4 mm.Size,in.Wall Thickness,in.ID Tolerance,in.OD Tolerance,in.213213213231321321324132132132613213236481321818101818181218181815181818TABLE 2 T
