1、Designation:B3310(Reapproved 2014)Standard Specification forTin-Coated Soft or Annealed Copper Wire for ElectricalPurposes1This standard is issued under the fixed designation B33;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the ye
2、ar of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers tin-coat
3、ed,round,soft,orannealed copper wire for electrical purposes.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.2.1 ExceptionsThe SI va
4、lues for density,resistivity,andvolume are to be regarded as standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the ap
5、plica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2B49 Specification for Copper Rod Drawing Stock for Elec-trical PurposesB193 Test Method for Resistivity of Electrical ConductorMaterialsB258 Specification for Nominal Diameters and Cross-SectionalAreas ofAW
6、G Sizes of Solid Round Wires Usedas Electrical Conductors2.2 Other Document:3NBS Handbook 100 Copper Wire Tables3.Ordering Information3.1 Orders for material under this specification shall includethe following information:3.1.1 Quantity of each size,3.1.2 Wire size-diameter in inches(see 5.3 and Tab
7、le 1),3.1.3 Type of copper,if special(see 4.2),3.1.4 Package size(see 10.1),3.1.5 Special packaging marking,if required,and3.1.6 Place of inspection(see 7.1).4.Material4.1 Tin for CoatingThe tin used for coating shall becommercially pure(Explanatory Note 1).For purposes of thisspecification,the tin
8、shall be considered commercially pure ifthe total of other elements,exclusive of copper,does notexceed 1%.Notwithstanding the previous sentence,chemicalanalysis of the tin coating or of the tin used for coating shall notbe required under this specification.Adequacy of the tincoating is assured by th
9、e continuity of coating and adherence ofcoating requirements(see 5.4 and 5.5,respectively).4.2 Copper-Base MetalThe base metal shall be copper ofsuch quality and purity that the finished product shall haveproperties and characteristics prescribed in this specification.NOTE1Specification B49 defines
10、copper suitable for use.4.3 Copper bars of special qualities,forms,or types,as maybe agreed upon between the manufacturer and the purchaser,and which will conform to the requirements prescribed in thisspecification,may also be used.5.General Requirements(See Section 8)5.1 Tensile Strength and Elonga
11、tion(Explanatory Note 2and Note 3)The tinned wire shall conform to the require-ments for elongation prescribed in Table 1.No requirementsfor tensile strength are specified.For wire whose nominaldiameter is more than 0.001 in.(0.025 mm)greater than a sizelisted in Table 1,but less than that of the ne
12、xt larger size,therequirements of the next larger size shall apply.5.2 Resistivity(Explanatory Note 1 and Note 4)The elec-trical resistivity of tinned wire at a temperature of 20C shallnot exceed the values prescribed in Table 2.5.3 Dimensions and Permissible Variations(ExplanatoryNote 2)The wire si
13、zes shall be expressed as the diameter ofthe wire in decimal fractions of an inch to the nearest 0.0001 in.1This specification is under the jurisdiction of ASTM Committee B01 onElectrical Conductors and is the direct responsibility of Subcommittee B01.04 onConductors of Copper and Copper Alloys.Curr
14、ent edition approved Sept.1,2014.Published September 2014.Originallyapproved in 1919.Last previous edition approved in 2010 as B33 10.DOI:10.1520/B0033-10R14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMS
15、tandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from National Technical Information Service(NTIS),5301 ShawneeRd.,Alexandria,VA 22312,http:/www.ntis.gov.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-29
16、59.United States1(0.0025 mm).The tin-coated wire shall not vary from thespecified diameter by more than the amounts prescribed inTable 3.5.4 Continuity of CoatingThe tin coating shall be continu-ous.The continuity of coating on the wire shall be determinedon representative samples taken before stranding or insulating.The continuity of tinning shall be determined by the hydro-chloric acid-sodium polysulfide test in accordance with 6.3.5.5 Adherence of CoatingThe tin coating shall be firmlyadheren
