1、Designation:A49295(Reapproved 2013)Standard Specification forStainless Steel Rope Wire1This standard is issued under the fixed designation A492;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in par
2、entheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This specification covers the more commonly used typesof round stainles
3、s steel wire intended especially for strandinginto wire rope.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2.Referenced Documents2.1
4、 ASTM Standards:2A555/A555M Specification for General Requirements forStainless Steel Wire and Wire RodsA751 Test Methods,Practices,and Terminology for Chemi-cal Analysis of Steel Products3.Ordering Information3.1 It is the responsibility of the purchaser to specify allrequirements that are necessar
5、y for material ordered under thisspecification.Such requirements may include,but are notlimited to the following:3.1.1 Quantity(weight),3.1.2 Name of material(stainless steel),3.1.3 Condition(see Section 5),3.1.4 Finish(see Section 7),3.1.5 Cross section(round),3.1.6 Form(wire),3.1.7 Applicable dime
6、nsions(diameter),3.1.8 Type designation(Table 1),3.1.9 ASTM designation and date of issue,and3.1.10 Special requirements.3.2 If possible,the intended end use of the item should begiven on the purchase order,especially when the item isordered for a specific end use or uses.NOTE1A typical ordering des
7、cription is as follows:1000 lb stainlesssteel,cold-drawn,bright-finish,wire,0.009-in.diameter,spools.Type304,ASTM Specification A492 dated,End Use.4.Chemical Composition4.1 The steel shall conform to the requirements as tochemical composition specified in Table 1.4.2 Methods and practices relating t
8、o chemical analysisrequired by this specification shall be in accordance with TestMethods,Practices,and Terminology A751.5.Condition5.1 The wire is cold drawn and furnished in the finish(seeSection 7)specified on the purchase order.6.Mechanical Requirements6.1 The material shall conform to the requi
9、rements as tomechanical properties specified in Table 2.7.Finish7.1 The types of finish procurable are pickled finish andbright finish(available only in sizes that can be diamonddrawn,which are generally 0.045 in.(1.14 mm)and smaller).8.General Requirements for Delivery8.1 In addition to the require
10、ments of this specification,allrequirements of the current edition of Specification A555/A555M,shall apply.Failure to comply with the generalrequirements of Specification A555/A555M constitutes non-conformance with this specification.9.Packaging and Package Marking9.1 Each coil or spool shall be one
11、 continuous length ofwire.Each coil shall be firmly tied and each spool shall betightly wound.Unless otherwise specified,coils shall be placedin drums or paper wrapped and spools shall be boxed in sucha manner as to assure safe delivery to their designation whenproperly transported by any common car
12、rier.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.17 on Flat-Rolled and Wrought Stainless Steel.Current edition approved Oct.1,2013.Published October 2013.Originallyapproved in 1963
13、.Last previous edition approved in 2009 as A492 95(2009).DOI:10.1520/A0492-95R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onth
14、e ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1Copyright by ASTM Intl(all rights reserved);9.2 Each coil or spool of wire shall be properly taggedshowing heat number,grade,condition,ASTM specificationnumber,and size.10.Keyw
15、ords10.1 austenitic stainless steel;stainless steel rope wireASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such pa
16、tent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresponsible tec
