收藏 分享(赏)

ASTM_A_350_-_A_350M_-_15.pdf

上传人:益****师 文档编号:186947 上传时间:2023-03-04 格式:PDF 页数:10 大小:274.91KB
下载 相关 举报
ASTM_A_350_-_A_350M_-_15.pdf_第1页
第1页 / 共10页
ASTM_A_350_-_A_350M_-_15.pdf_第2页
第2页 / 共10页
ASTM_A_350_-_A_350M_-_15.pdf_第3页
第3页 / 共10页
ASTM_A_350_-_A_350M_-_15.pdf_第4页
第4页 / 共10页
ASTM_A_350_-_A_350M_-_15.pdf_第5页
第5页 / 共10页
ASTM_A_350_-_A_350M_-_15.pdf_第6页
第6页 / 共10页
亲,该文档总共10页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:A350/A350M15Standard Specification forCarbon and Low-Alloy Steel Forgings,Requiring NotchToughness Testing for Piping Components1This standard is issued under the fixed designation A350/A350M;the number immediately following the designation indicates the yearof original adoption or,in th

2、e case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This

3、specification2covers several grades of carbon andlow-alloy steel forged or ring-rolled flanges,forged fittings andvalves intended primarily for low-temperature service andrequiring notch toughness testing.They are made to specifieddimensions,or to dimensional standards,such as the ASMEand API Specif

4、ications referenced in Section 2.Although thisspecification covers some piping components machined fromrolled bar and seamless tubular materials(see 5.3.3),it does notcover raw material produced in these product forms.1.2 No limitation on size is intended beyond the ability ofthe manufacturer to obt

5、ain the specified requirements.However,Class 3 of Grade LF787 is only available in thequenched-and-precipitation heat treated condition.1.3 Supplementary requirements are provided for use whenadditional testing or inspection is desired.These shall applyonly when specified by the purchaser in the ord

6、er.1.4 This specification is expressed in both inch-pound unitsand in SI units.However,unless the order specifies theapplicable“M”specification designation(SI units),the mate-rial shall be furnished to inch-pound units.1.5 The values stated in either SI units or inch-pound unitsare to be regarded se

7、parately as standard.Within the text,theSI units are shown in brackets.The values stated in eachsystem may not be exact equivalents;therefore,each systemshall be used independently of the other.Combining valuesfrom the two systems may result in non-conformance with thestandard.2.Referenced Documents

8、2.1 ASTM Standards:3A788/A788M Specification for Steel Forgings,General Re-quirementsA961/A961M Specification for Common Requirements forSteel Flanges,Forged Fittings,Valves,and Parts forPiping Applications2.2 ASME Standards:B 16.5 Steel Pipe Flanges and Flanged Fittings4B 16.9 Factory-Made Wrought

9、Steel Butt-Welding Fittings4B 16.10Face-to-Face and End-to-End Dimensions ofFerrous Valves4B 16.11Forged Steel Fittings,Socket-Welding andThreaded4B 16.30 Unfired Pressure Vessel Flange Dimensions4B 16.34 Valves-Flanged,Threaded,and Welding End4B 16.47 Large Diameter Steel Flanges42.3 ASME Boiler an

10、d Pressure Vessel Code:Section IX22.4 AWS Standards:A 5.1 Mild Steel Covered Arc-Welding Electrodes5A 5.5 Low-Alloy Steel Covered Arc-Welding Electrodes52.5 API Standards:6600 Steel Gate Valves with Flanged or Butt-Welding Ends602 Compact Design Carbon Steel Gate Valves for RefineryUse605 Large Diam

11、eter Carbon Steel Flanges3.Ordering Information3.1 It is the purchasers responsibility to specify in thepurchase order information necessary to purchase the needed1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct respons

12、ibility of SubcommitteeA01.22 on Steel Forgings and Wrought Fittings for Piping Applications and BoltingMaterials for Piping and Special Purpose Applications.Current edition approved May 1,2015.Published May 2015.Originallyapproved in 1952.Last previous edition approved in 2014 as A350/A350M14.DOI:1

13、0.1520/A0350_A0350M-15.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-350 in Section II of that Code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume inf

14、ormation,refer to the standards Document Summary page onthe ASTM website.4Available from American Society of Mechanical Engineers(ASME),ASMEInternational Headquarters,Two Park Ave.,New York,NY 10016-5990,http:/www.asme.org.5Available from American Welding Society(AWS),550 NW LeJeune Rd.,Miami,FL 331

15、26,http:/www.aws.org.6Available from American Petroleum Institute(API),1220 L.St.,NW,Washington,DC 20005-4070,http:/api-ec.api.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United St

16、ates1 material.In addition to the ordering information guidelines inSpecification A961/A961M,orders should include the follow-ing information:3.1.1 The number of test reports required(see Section 14).3.1.2 Additional requirements(see Table 1 footnotes).3.1.3 Options in the specification.See 5.4.2.1.4.General Requirements4.1 Product furnished to this specification shall conform tothe requirements of Specification A961/A961M,including anysupplementary requirements that are indicated in the purchas

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2