1、Designation:A62316Standard Specification forTin Mill Products,General Requirements1This standard is issued under the fixed designation A623;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parenth
2、eses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 Thisspecificationcoversagroupofcommonrequirements,which unless otherwis
3、e specified in the purchaseorder or in an individual specification,shall apply to tin millproducts.1.2 In case of any conflict in requirements,the requirementsof the purchase order,the individual material specification,andthis general specification shall prevail in the sequence named.NOTE1Acomplete
4、metric companion to Specification A623 has beendevelopedSpecification A623M;therefore no metric equivalents arepresented in this specification.1.3 The following safety caveat covers Annex A3 throughAnnex A10 of this specification:This standard does notpurport to address all of the safety concerns,if
5、 any,associatedwith its use.It is the responsibility of the user of this standardto establish appropriate safety and health practices anddetermine the applicability of regulatory limitations prior touse.2.Referenced Documents2.1 ASTM Standards:2A370 Test Methods and Definitions for Mechanical Testin
6、gof Steel ProductsA700 Guide for Packaging,Marking,and Loading Methodsfor Steel Products for ShipmentA987 Practice for Measuring Shape Characteristics of TinMill ProductsD1125 Test Methods for Electrical Conductivity and Resis-tivity of WaterE18 Test Methods for Rockwell Hardness of Metallic Ma-teri
7、alsE112 Test Methods for Determining Average Grain Size2.2 U.S.Military Standards:3MIL-STD-129 Marking for Shipment and StorageMIL-STD-163 Steel Mill Products,Preparation for Markingand Storage2.3 U.S.Federal Standard:3Federal Std.No.123 Marking for Shipment(CivilAgencies)3.Terminology3.1 Definition
8、s:3.1.1 base box,na unit of area equivalent to 112 sheets 14by 20 in.or 31 360 in.2(217.78 ft2)(see Annex A1).3.1.2 base weight,na term used to describe the thicknessof tin mill products.The designated base weight multiplied bya factor of 0.00011 is the nominal decimal thickness,in inchesof the mate
9、rial.Although it is customary industry-wide to usethe term“pound”(for example,75 lb),following the baseweight designation,base weight is correctly used only to definenominal material thickness,and is not a measure of the weightof a base box.3.1.3 black plate,nlight-gage,low-carbon,cold-reducedsteel
10、intended for use in the untinned state or for the productionof other tin mill products.It is supplied only in a dry or oiledcondition.3.1.4 box annealing,na process involving slow heating ofcoils to a subcritical temperature,holding,and coolingtherefrom,to soften the strip and relieve stresses produ
11、cedduring cold reduction.It is accomplished in a sealed container.By introducing and maintaining an inert or slightly reducingatmosphere during the cycle,a relatively bright surface isobtained.3.1.5 bright finish,na surface that has a melted tincoating.3.1.6 bundle,na unit containing two or more pac
12、kages ofa cut size,supported by a platform,generally consisting of tenor more packages.(Also commonly referred to as a multiple-package lift containing two or more packages.)3.1.7 burr,nmetal displaced beyond the plane of thesurface by slitting or shearing(see 9.1.7 and 9.2.6).1This specification is
13、 under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.20 on Tin Mill Products.Current edition approved Dec.1,2016.Published December 2016.Originallyapproved in 1968.Last previous edition approved in 2011 as A623-
14、11.DOI:10.1520/A0623-16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents
15、Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.1.8 camber,nthe greatest deviation of a coil edge froma straight line.The measurement is taken on the conc
16、ave sideand is the perpendicular distance from a straight line to thepoint of maximum deviation(see 9.1.9 and 9.2.7).3.1.9chemical treatment,electrolytic tin plate,na passi-vating chemical treatment applied to the surface of electrolytictin plate to stabilize the plate surface characteristics compatiblewith a specified end use(see Annex A8 and Annex A10).3.1.10chemically treated steel,nlight-gage,low-carbon,cold-reduced steel that has a passivating or chemical treatmentapplied to the surface to
