1、Designation:A1016/A1016M17Standard Specification forGeneral Requirements for Ferritic Alloy Steel,AusteniticAlloy Steel,and Stainless Steel Tubes1This standard is issued under the fixed designation A1016/A1016M;the number immediately following the designation indicates theyear of original adoption o
2、r,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers a group of requirements that,unless otherwise specified in
3、 an individual specification,shallapply to the ASTM product specifications noted below.Title of SpecificationASTMDesignationASeamless Carbon-Molybdenum Alloy-Steel Boiler andSuperheater TubesA209/A209MSeamless Ferritic and Austenitic Alloy-Steel Boiler,Superheater,and Heat-Exchanger TubesA213/A213MW
4、elded Austenitic Steel Boiler,Superheater,Heat-Exchanger,and Condenser TubesA249/A249MElectric-Resistance-Welded Ferritic Alloy-Steel Boiler andSuperheater TubesA250/A250MSeamless and Welded Ferritic and Martensitic Stainless SteelTubing for General ServiceA268/A268MSeamless and Welded Austenitic St
5、ainless Steel Tubing forGeneral ServiceA269/A269MSeamless and Welded Austenitic Stainless Steel SanitaryTubingA270/A270MSeamless and Welded Carbon and Alloy-Steel Tubes forLow-Temperature ServiceA334/A334MWelded Austenitic Stainless Steel Feedwater Heater TubesA688/A688MAustenitic Stainless Steel Tu
6、bing for Breeder Reactor CoreComponentsA771/A771MSeamless and Welded Ferritic/Austenitic Stainless Steel Tubingfor General ServiceA789/A789MWelded Ferritic Stainless Steel Feedwater Heater TubesA803/A803MAustenitic and Ferritic Stainless Steel Duct Tubes for BreederReactor Core ComponentsA826/A826MH
7、igh-Frequency Induction Welded,Unannealed Austenitic SteelCondenser TubesA851AThese designations refer to the latest issue of the respective specifications.1.2 In the case of conflict between a requirement of aproduct specification and a requirement of this general require-ments specification,the pr
8、oduct specification shall prevail.Inthe case of conflict between a requirement of the productspecification or a requirement of this general requirementsspecification and a more stringent requirement of the purchaseorder,the purchase order shall prevail.1.3 The values stated in either SI units or inc
9、h-pound unitsare to be regarded separately as standard.Within the text,theSI units are shown in brackets.The values stated in eachsystem may not be exact equivalents;therefore,each systemshall be used independently of the other.Combining valuesfrom the two systems may result in non-conformance with
10、thestandard.The inch-pound units shall apply unless the“M”designation(SI)of the product specification is specified in theorder.2.Referenced Documents2.1 ASTM Standards:2A209/A209M SpecificationforSeamlessCarbon-Molybdenum Alloy-Steel Boiler and Superheater TubesA213/A213M Specification for Seamless
11、Ferritic and Aus-tenitic Alloy-Steel Boiler,Superheater,and Heat-Exchanger TubesA249/A249M Specification for Welded Austenitic SteelBoiler,Superheater,Heat-Exchanger,and CondenserTubesA250/A250M Specification for Electric-Resistance-WeldedFerritic Alloy-Steel Boiler and Superheater TubesA268/A268M S
12、pecification for Seamless and Welded Fer-ritic and Martensitic Stainless Steel Tubing for GeneralServiceA269/A269M Specification for Seamless and Welded Aus-tenitic Stainless Steel Tubing for General ServiceA270/A270M Specification for Seamless and Welded Aus-tenitic and Ferritic/Austenitic Stainles
13、s Steel SanitaryTubingA334/A334M Specification for Seamless and Welded Car-bon and Alloy-Steel Tubes for Low-Temperature ServiceA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA530/A530M Specification for General Requirements forSpecialized Carbon and Alloy Steel PipeA688/A6
14、88M Specification for Seamless and Welded Aus-tenitic Stainless Steel Feedwater Heater Tubes1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.10 on Stainless and Alloy Steel Tubular Prod
15、ucts.Current edition approved March 15,2017.Published March 2017.Originallyapproved in 2001.Last previous edition approved in 2014 as A1016/A1016M 141.DOI:10.1520/A1016_A1016M-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For
16、 Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides a
