1、Designation:A105814An American National StandardStandard Test Methods forMechanical Testing of Steel ProductsMetric1This standard is issued under the fixed designation A1058;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of
2、 last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 These test methods cover mechanical tests described inASTM,EN,2ISO,3and JIS4standards that utilize the SI systemof units.
3、The test methods in each system are not exactequivalents.Each standards system(ASTM,EN,ISO,and JIS)shall be used independently of the other.Combining require-ments from any two or more systems may result in noncon-formance with the purchase order.1.2 These test methods cover procedures for the mecha
4、nicaltesting of steels,stainless steels,and related alloys.The variousmechanical tests herein described are used to determine prop-erties required in the product specifications.Variations intesting methods are to be avoided,and standard methods oftesting are to be followed to obtain reproducible and
5、 compa-rable results.In those cases in which the testing requirementsfor certain products are unique or at variance with these generalprocedures,the product specification testing requirements shallcontrol.1.3 Only one of the testing procedure tracks shall befollowed:ASTM,EN,ISO,or JIS.When a test me
6、thod orpractice is not available in one of the tracks then an appropriatetest method or practice from an alternative track shall be used.The respective tests are listed in the column shown in Table 1.NOTE1The test methods in each system are not exact equivalents.1.4 The values stated in SI units are
7、 to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 Attention is directed to Practice ISO 17025 when theremay be a need for information on criteria for evaluation oftesting laboratories.1.6 This standard does not purport to address all of thesafety concerns,if a
8、ny,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:5A833 Practice for Indentation Hardness of Metallic M
9、ateri-als by Comparison Hardness TestersA956 Test Method for Leeb Hardness Testing of SteelProductsA1038 Test Method for Portable Hardness Testing by theUltrasonic Contact Impedance MethodE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE10 Test Method for Brinell Hardness of Metallic M
10、aterialsE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE23 Test Methods for Notched Bar Impact Testing of Me-tallic MaterialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE110 Test Method for Rockwell and Brinell Hardness ofMetallic M
11、aterials by Portable Hardness TestersE190 Test Method for Guided Bend Test for Ductility ofWeldsE290 Test Methods for Bend Testing of Material for Ductil-ity2.2 Other Documents:ASME Boiler and Pressure Vessel Code Section VIII,Divi-sion I6ISO 148-1 Metallic MaterialsCharpy Pendulum ImpactTestPart 1:
12、Test Method7ISO 148-2 Metallic MaterialsCharpy Pendulum Impact1These test methods are under the jurisdiction of ASTM Committee A01 onSteel,Stainless Steel and Related Alloys and are the direct responsibility ofSubcommittee A01.13 on Mechanical and Chemical Testing and ProcessingMethods of Steel Prod
13、ucts and Processes.Current edition approved May 15,2014.Published June 2014.Originallyapproved in 2008.Last previous edition approved in 2012 as A1058 12b.DOI:10.1520/A1058-14.2Available from British Standards Institute(BSI),389 Chiswick High Rd.,London W4 4AL,U.K.,http:/www.bsi-.3Available from Int
14、ernational Organization for Standardization,1 rue deVaremb,Case postale,CH-1211,Genve 20,Switzerland,http:/www.iso.org.4Available from Japanese Standards Association,4-1-24,Akasaka,Minato-ku,Tokyo,107-8440,Japan,http:/www.jsa.or.jp.5For referenced ASTM standards,visit the ASTM website,www.astm.org,o
15、rcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.6Available from American Society of Mechanical Engineers,ASMEInternational,Three Park Avenue,New York,NY 10016-5990,USA,http:/www.asme
16、.org.7These standards are also designed EN ISO:this identifies the adoption of ISOstandards by EN.“EN ISO”is part of the designation.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1Copyright by ASTM Intl(all rights reserved);TestPart 2:Verification of Test Machines7ISO 2566-1 SteelConversion of Elongation ValuesPart1:Carbon and Low Alloy Steels7ISO 2566-2 SteelConversion
