1、Designation:B111/B111M16Standard Specification forCopper and Copper-Alloy Seamless Condenser Tubes andFerrule Stock1This standard is issued under the fixed designation B111/B111M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the ye
2、ar of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification2establishes
3、 the requirements forseamless tube and ferrule stock of copper and various copperalloys up to 318in.80 mm inclusive,in diameter,for use insurface condensers,evaporators,and heat exchangers.Thefollowing coppers and copper alloys are specified:3Copper or CopperAlloy UNS No.Previously UsedDesignationDe
4、scriptionC10100OFEOxygen-free electronicC10200OFAOxygen-free without residual deoxidantsC10300.Oxygen-free,extra low phosphorusC10800.Oxygen-free,low phosphorusC12000DLPAPhosphorized,low residual phosphorusC12200DHPAPhosphorized,high residual phosphorusC14200DPAAPhosphorized,arsenicalC19200.Phosphor
5、ized,1%ironC23000.Red BrassC28000.Muntz MetalC44300.Admiralty Metals,B,C,and DC44400.C44500.C60800.Aluminum BronzeC61300.C61400.Aluminum Bronze,DC68700.Aluminum Brass,BC70400.95-5 Copper-NickelC70600.90-10 Copper-NickelC70620.90-10 Copper-NickelWelding GradeC71000.80-20 Copper-NickelC71500.70-30 Cop
6、per-NickelC71520.70-30 Copper-NickelWelding GradeC71640.Copper-nickel-iron-manganeseC72200.ADesignations listed in Classification B224.1.2 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivale
7、nts;therefore,each system shall be used independently of the other.Combining values from the two systems may result in non-conformance with the standard.1.3 The following safety hazards caveat pertains only to thetest methods portion,Section 19,of this specification:Thisstandard does not purport to
8、address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.(WarningMercury has been designated bymany regulatory age
9、ncies as a hazardous substance that cancause serious medical issues.Mercury,or its vapor,has beendemonstrated to be hazardous to health and corrosive tomaterials.Caution should be taken when handling mercury andmercury containing products.See the applicable product SafetyData Sheet(SDS)for additiona
10、l information.Users should beaware that selling mercury and/or mercury containing productsin your state or country may be prohibited by law.)2.Referenced Documents2.1 The following documents in the current issue of theAnnual Book of ASTM Standards form a part of this specifi-cation to the extent ref
11、erenced herein:2.2 ASTM Standards:4B153 Test Method for Expansion(Pin Test)of Copper andCopper-Alloy Pipe and TubingB154 Test Method for Mercurous Nitrate Test for CopperAlloysB170 Specification for Oxygen-Free Electrolytic CopperRefinery ShapesB224 Classification of CoppersB846 Terminology for Copp
12、er and Copper AlloysB858 Test Method forAmmonia Vapor Test for DeterminingSusceptibility to Stress Corrosion Cracking in CopperAlloys1This specification is under the jurisdiction ofASTM Committee B05 on Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.04 on Pipeand Tube.C
13、urrent edition approved Oct.1,2016.Published November 2016.Originallyapproved in 1937.Last previous edition approved in 2011 as B111/B111M11.DOI:10.1520/B0111_B0111M-16.2For ASME Boiler and Pressure Vessel Code applications,see related Specifi-cation SB-111 in Section II of the Code.3The UNS system
14、for copper and copper alloys(see Practice E527)is a simpleexpansion of the former standard designation system accomplished by the additionof a prefix“C”and a suffix“00.”The suffix can be used to accommodatecomposition variations of the base alloy.4For referenced ASTM standards,visit the ASTM website
15、,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO
16、Box C700,West Conshohocken,PA 19428-2959.United States1 B968/B968M Test Method for Flattening of Copper andCopper-Alloy Pipe and TubeE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE53 Test Method for Determination of Copper in UnalloyedCopper by GravimetryE54 Test Methods for Chemical Analysis of Special Brassesand Bronzes(Withdrawn 2002)5E62 Test Methods for Chemical Analysis of Copp
