1、Designation:A564/A564M13Standard Specification forHot-Rolled and Cold-Finished Age-Hardening Stainless SteelBars and Shapes1This standard is issued under the fixed designation A564/A564M;the number immediately following the designation indicates the yearof original adoption or,in the case of revisio
2、n,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope*1.1 This specification2covers
3、bars and shapes of age-hardening stainless steels.Hot-finished or cold-finished rounds,squares,hexagons,bar shapes,angles,tees,and channels areincluded;these shapes may be produced by hot rolling,extruding,or forging.Billets or bars for reforging may bepurchased to this specification.1.2 These steel
4、s are generally used for parts requiringcorrosion resistance and high strength at room temperature,orat temperatures up to 600F 315C;700F 370C for Type632;840F 450C for Type UNS S46910.They are suitablefor machining in the solution-annealed condition after whichthey may be age-hardened to the mechan
5、ical properties speci-fied in Section 7 without danger of cracking or distortion.TypeXM-25 is machinable in the as-received fully heat treatedcondition.Type UNS S46910 is suitable for machining in thesolution-annealed,cold-worked,and aged-hardened condition.1.3 Types 631 and 632 contain a large amou
6、nt of ferrite inthe microstructure and can have low ductility in forgings andlarger diameter bars.Applications should be limited to smalldiameter bar.1.4 The values stated in either inch-pound units or SI(metric)units are to be regarded separately as standards;withinthe text and tables,the SI units
7、are shown in brackets.Thevalues stated in each system are not exact equivalents;therefore,each system must be used independent of the other.Combining values from the two systems may result in noncon-formance with the specification.1.5 Unless the order specifies an“M designation,thematerial shall be
8、furnished to inch-pound units.NOTE1For forgings,see Specification A705/A705M.NOTE2For billets and bars for forging see Specification A314.2.Referenced Documents2.1 ASTM Standards:3A314 Specification for Stainless Steel Billets and Bars forForgingA370 Test Methods and Definitions for Mechanical Testi
9、ngof Steel ProductsA484/A484M Specification for General Requirements forStainless Steel Bars,Billets,and ForgingsA705/A705M Specification for Age-Hardening StainlessSteel ForgingsA751 Test Methods,Practices,and Terminology for Chemi-cal Analysis of Steel ProductsE527 Practice for Numbering Metals an
10、d Alloys in theUnified Numbering System(UNS)2.2 Other Documents:SAE J1086 Recommended Practice for Numbering Metalsand Alloys(UNS)43.Ordering Information3.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification.Such requi
11、rements may include but are notlimited to the following:3.1.1 Quantity(weight or number of pieces),3.1.2 Type or UNS designation(Table 1),3.1.3 Specific melt type when required,3.1.4 Heat treated condition(5.1),3.1.5 Transverse properties when required(7.6),3.1.6 Finish(Specification A484/A484M),3.1
12、.7 Surface preparation of shapes(5.2.1),3.1.8 Size,or applicable dimension including diameter,thickness,width,length,etc.,3.1.9 Preparation for delivery(Specification A484/A484M),1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is th
13、e direct responsibility of SubcommitteeA01.17 on Flat-Rolled and Wrought Stainless Steel.Current edition approved May 1,2013.Published July 2013.Originally approvedin 1966.Last previous edition approved in 2010 as A564/A564M 10.DOI:10.1520/A0564_A0564M-13.2For ASME Boiler and Pressure Vessel Code ap
14、plications,see related Specifi-cation SA-564/SA-564M in Section II of that Code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe
15、 ASTM website.4Available from Society of Automotive Engineers(SAE),400 CommonwealthDr.,Warrendale,PA 15096-0001,http:/www.sae.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United Sta
16、tes1Copyright by ASTM Intl(all rights reserved);3.1.10 Special requirements(refer to 7.4 and 8.3),3.1.11 Marking requirements(Specification A484/A484M),and3.1.12 ASTM designation and date of issue if other than thatcurrently published.3.2 If possible,the intended use of the item should be givenon the purchase order especially when the item is ordered fora specific end use or uses.NOTE3Atypical ordering description is as follows:5000 lb 2270 kgType 630,Solution-Annealed Cold Finished Centerless G
