收藏 分享(赏)

ASTM_F_104_-_11.pdf

上传人:益****师 文档编号:187997 上传时间:2023-03-04 格式:PDF 页数:12 大小:119.02KB
下载 相关 举报
ASTM_F_104_-_11.pdf_第1页
第1页 / 共12页
ASTM_F_104_-_11.pdf_第2页
第2页 / 共12页
ASTM_F_104_-_11.pdf_第3页
第3页 / 共12页
ASTM_F_104_-_11.pdf_第4页
第4页 / 共12页
ASTM_F_104_-_11.pdf_第5页
第5页 / 共12页
ASTM_F_104_-_11.pdf_第6页
第6页 / 共12页
亲,该文档总共12页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:F10411Standard Classification System forNonmetallic Gasket Materials1This standard is issued under the fixed designation F104;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revision.Anumber in parenthese

2、s indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This classification system2provides a means for speci-fying or describing perti

3、nent properties of commercial nonme-tallic gasket materials.Materials composed of asbestos,cork,cellulose,and other organic or inorganic materials in combi-nation with various binders or impregnants are included.Materials normally classified as rubber compounds are notincluded,since they are covered

4、 in Classification D2000.Gasket coatings are not covered,since details thereof areintended to be given on engineering drawings or in separatespecifications.Facing materials for laminate composite gasketmaterials(LCGM)are included in Classification System F104.Assembled LCGMs are covered in Classific

5、ation F868.1.2 Since all of the properties that contribute to gasketperformance are not included,use of the classification systemas a basis for selecting materials is limited.1.3 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1

6、.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Docume

7、nts2.1 ASTM Standards:2C561 Test Method for Ash in a Graphite SampleD1170 Specification for Nonmetallic Gasket Materials forGeneral Automotive and Aeronautical Purposes(With-drawn 1968)3D2000 Classification System for Rubber Products in Auto-motive ApplicationsD5964 Practice for Rubber IRM 901,IRM 9

8、02,and IRM903 Replacement Oils forASTM No.1,ASTM No.2,andASTM No.3 OilsE11 Specification for Woven Wire Test Sieve Cloth and TestSievesF36 Test Method for Compressibility and Recovery of Gas-ket MaterialsF37 Test Methods for Sealability of Gasket MaterialsF38 Test Methods for Creep Relaxation of a G

9、asket MaterialF146 Test Methods for Fluid Resistance of Gasket MaterialsF147 Test Method for Flexibility of Non-Metallic GasketMaterialsF148 Test Method for Binder Durability of Cork Composi-tion Gasket MaterialsF152 Test Methods for Tension Testing of NonmetallicGasket MaterialsF433 Practice for Ev

10、aluating Thermal Conductivity of Gas-ket MaterialsF607 Test Method for Adhesion of Gasket Materials toMetal SurfacesF868 Classification for Laminated Composite Gasket Mate-rialsF1315 Test Method for Density of a Sheet Gasket MaterialG21 Practice for Determining Resistance of Synthetic Poly-meric Mat

11、erials to Fungi3.Significance and Use3.1 This classification system is intended to encourageuniformity in reporting properties;to provide a commonlanguage for communications between suppliers and consum-ers;to guide engineers and designers in the test methodscommonly used for commercially available

12、materials;and tobe versatile enough to cover new materials and test methods asthey are introduced.3.2 This system is based on the principle that nonmetallicgasket materials can be described in terms of specific physicaland mechanical properties.This enables the user,or producer,to characterize a non

13、metallic gasket based on properties thatare important for the application.1This classification is under the jurisdiction of ASTM Committee F03 onGaskets and is the direct responsibility of Subcommittee F03.30 on Classification.Current edition approved April 1,2011.Published May 2011.Originallyapprov

14、ed in 1968.Last previous edition approved in 2009 as F104 03(2009).DOI:10.1520/F0104-11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary pa

15、ge onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.Basis of Classification4.1 To permit“line call-out”of a materials physical andmech

16、anical properties,this classification system establishesletter and number symbols for various performance levels ofeach property or characteristic.4.2 Each“line call out”shall include:-ASTM F104-In parentheses,the letter“F”followed by 6 numeralsdescribing the required basic characteristics per 8.1.-Within the same parentheses,a dash“-”shall follow the basiccharacteristics,along with any supplemental characteristics per8.2.All six(6)numeric fields defining the basic characteristicsmust be occupie

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2