1、Designation:F132215An American National StandardStandard Guide forSelection of Shipboard Incinerators1This standard is issued under the fixed designation F1322;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision
2、.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide covers selection criteria to assist procurers inselecting the appropriate incinerator for their needs.1.2 This guide is a com
3、panion document to SpecificationF1323.1.3 This guide does not apply to incinerator systems onspecial incinerator ships,for example,for burning industrialwastes such as chemicals,manufacturing residues,and soforth.1.4 The values stated in SI units are to be regarded asstandard.The values given in par
4、entheses are mathematicalconversions to inch-pound units that are provided for informa-tion only and are not considered standard.2.Referenced Documents2.1 ASTM Standards:2F1323 Specification for Shipboard Incinerators2.2 Other Document:3MARPOL 73783.Terminology3.1 Definitions:3.1.1 batch feeding,nno
5、n-continuous feeding incineratorwhere the combustion chamber shall be cooled down betweenplacing solid waste into the combustion chamber.3.1.2 continuous feeding,npump transfer of sludge oilinto the incinerator combustion chamber on a continuous basis;also,the feeding of solid waste into the combust
6、ion chamberby a screw conveyor or sluice system.3.1.3 sludge oil,nresidual from fuel and lubricating oilseparators,oily waste from machinery and hydraulic powerunits,drip trays,and oil-water separators.3.1.4 sluice system,ntrap door system,whereby it ispossible in a safe manner to feed solid waste i
7、nto thecombustion chamber while the incinerator is operating at hightemperature.3.1.5 solid waste,ncombustible trash,garbage,and rub-bish(see also 7.4).3.1.6 waste,nunneeded or useless matter which is to bediscarded.4.Selecting the Incinerator Size and Installed Location4.1 Anumber of factors will g
8、overn the selection of the sizeand type of shipboard incinerator and full consideration mustbe given to each.The installed operating location of the unit isof equal importance to ensure low-cost operating,ease ofcharging,ease of cleaning,and so forth.Consideration shouldbe given to the following:4.1
9、.1 Maximum amount of each type of waste that will beincinerated each day(see Section 5).4.1.2 The normal number of hours per day that the incin-erator will be in operation.4.1.3 Loading procedure(batch/continuous)over operatinghours.4.1.4 Can wet and dry material be loaded into the incinera-tor so t
10、hat a large volume of auxiliary fuel is not required?4.1.5 Can the incinerator be installed on the ship in alocation near the major source of refuse so as to minimize themanpower requirements during loading operations?4.1.6 Ash removal,if the incinerator is installed in themachinery space or on a lo
11、wer deck.4.1.7 Will ash removal be manual(shoveling)or semiauto-matic(plow)?5.Estimating Daily Quantities of Waste to BeIncinerated5.1 Size of Ships Crew:5.1.1 Galley and crew quarters waste estimate:1.5 kg(3.3lb)per crew member per day.5.2 Number of Passengers Carried:5.2.1 Galley and passenger qua
12、rters waste estimate:2.5 kg(5.5 lb)per passenger per day.5.3 StoresEstimated amount of packaging for food andother items that,during the underway period,will become1This guide is under the jurisdiction of ASTM Committee F25 on Ships andMarine Technology and is the direct responsibility of Subcommitt
13、ee F25.06 onMarine Environmental Protection.Current edition approved May 1,2015.Published July 2015.Originally approvedin 1990.Last previous edition approved in 2009 as F1322 90(2009).DOI:10.1520/F1322-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Serv
14、ice at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from International Maritime Organization(IMO),4,AlbertEmbankment,London,UK,SEI 7SR,http:/www.imo.org.Copyright ASTM International,100 Barr Harbor Driv
15、e,PO Box C700,West Conshohocken,PA 19428-2959.United States1 waste in the form of rubbish or trash;0.5 kg(1.1 lb)per crewmember or passenger per day.5.4 Sludge oil generation(see 8.3).6.Other Factors for Selection6.1 Type of Unit(for example:solid waste only,solid wasteand sludge oil).6.2 Capacity o
16、f unit in kW or BTU/hr(based on wastegeneration estimate,heat content of waste,and operatinghours).6.3 Sludge oil capacity.6.4 Loading considerations(batch loading or continuousfeed).6.5 Installation considerations(indoor/outdoor).6.6 Environmental considerations(incinerators are normallyrequired to meet the emission limits specified in IMO MAR-POL 73/78,Annex VI).6.7 Heat recover options(amount of steam or hot water).6.8 Ash removal.6.9 Induced draft fan requirements.6.10 Modular/package constr
